|
|
|
Normally, the XCOMPLEX Admin Server is brought up first, then the XCOMPLEX Worker Servers, although this is not required.
To start a CA XCOM Data Transport XCOMPLEX Admin Server, enter one of the following commands on the z/OS console (or any TSO/ISPF or NETVIEW session) where you are authorized to invoke z/OS system commands:
START XCOMAD
S XCOMAD
Many of the messages that are displayed when you start the XCOMPLEX Admin Servers are the same as when you start a stand‑alone server, but the following example shows some of the additional messages you will see. Note the XCOMM0045I message, which indicates that an XCOMPLEX Worker Server has successfully connected to the XCOMPLEX Admin Server.
XCOMM0990I ACTUAL XCOMDFLT PARMS:
.
.
.
XCOMM0991I XCOMPLEX=XCOMPLEX_QA
XCOMM0991I WINNERS =000004
XCOMM1196I THE XCOMXADM (ADMIN) SERVER HAS BEEN DEPRECATED AS OF r11.6.
XCOMM1197I PLEASE CONSULT THE ADMINISTRATION GUIDE FOR INFORMATION REGARDING USING
PLEXQ FOR XCOMPLEX SERVICES
XCOMM0008I XCPT ACB OPENED SUCCESSFULLY
XCOMM0009I COMPILED UNDER VTAM V5 R1 MC ‑ EXECUTING UNDER VTAM V6 R1 MC
5695‑11701‑1C0
XCOMM0763I DEFAULT TABLE XCPTDFB5 LOADED. GENERATED 08/19/02 AT 11.56
XCOMM0027I ESTAE ROUTINE HAS BEEN ESTABLISHED
XCOMM0056I CA XCOM (R) r11.6 (GEN LEVEL 0410 SP00) IS UP AND ACCEPTING LOGONS
XCOMM0056I ON CPU 2064 SERIAL # 240AA1 IN 31‑BIT MODE MVS SP7.0.2
XCOMM1000I CROSS‑COUPLING FACILITY LISTENER TASK STARTING
XCOMM1000I STARTING CROSS‑SYSTEM COUPLING FACILITY SERVICE TASK
XCOMM0559I XCOMPU ENABLED SUCCESSFULLY
XCOMM0559I XCOMPS ENABLED SUCCESSFULLY
XCOMM0559I XCOMPV ENABLED SUCCESSFULLY
XCOMM0559I XCOMMVS4 ENABLED SUCCESSFULLY
XCOMM1019I XCF CONNECT STR=XCOMPLEX_QA , CONN=XCPT , RC=00000000,
RSN=00000000, DISP=OLD
XCOMM1020I MAXIMUM SERVERS SUPPORTED=00000061
XCOMM1054I MAXIMUM LIST ENTRIES SUPPORTED=00001673
XCOMM1017I XCF READING MASTER ENTRY FROM LIST #0000
XCOMM1013I XCF REQ=READ RC=00000000 REASON=00000000 LIST=0000
ENTRY=XCOMPLEX_QA
XCOMM1022I LOCATING SERVER ENTRY IN LIST #0000
XCOMM1026I UPDATING MASTER ENTRY IN LIST #0000
XCOMM1013I XCF REQ=WRITE RC=00000000 REASON=00000000 LIST=0000
ENTRY=XCOMPLEX_QA
XCOMM1028I ADDING SERVER ENTRY FOR NODE (XCPT ) WHICH IS USING LIST #0002
XCOMM1013I XCF REQ=LOCK (SET) RC=00000000 REASON=00000000 LIST=0002
XCOMM1013I XCF REQ=WRITE RC=00000000 REASON=00000000 LIST=0000 ENTRY=
XCOMM1055I CLEARING LIST #0063 FOR USE BY NODE(XCPT )
XCOMM1013I XCF REQ=DELETE_MULT RC=00000000 REASON=00000000 LIST=0063
XCOMM1013I XCF REQ=MONITOR_LIST RC=00000000 REASON=00000000 LIST=0063
XCOMM1013I XCF REQ=LOCK (RESET) RC=00000000 REASON=00000000 LIST=0002
XCOMM0719I SESSION ESTABLISHED WITH PLU=XCOMMVS4, MODE=SNASVCMG, CID=04000061,
DEST=XCOMMVS4, SRUSIZE=00256, RRUSIZE=00256
XCOMM0618I REMOTE CNOS REQUEST PROCESSED SUCCESSFULLY
XCOMM0451I XCOMMVS4 NOW CONNECTED TO XCOMPLEX Admin Server XCPT
XCOMM0719I SESSION ESTABLISHED WITH PLU=XCPV , MODE=SNASVCMG, CID=3800000E,
DEST=XCOMPV , SRUSIZE=00256, RRUSIZE=00256
XCOMM0618I REMOTE CNOS REQUEST PROCESSED SUCCESSFULLY
XCOMM0451I XCOMPV NOW CONNECTED TO XCOMPLEX Admin Server XCPT
| Copyright © 2012 CA. All rights reserved. |
|