Commands › LDTM Command › LDTM Examples

LDTM Examples

This example evaluates all fixed LDTM requirements with no outage.

LDTM

This example evaluates all fixed LDTM requirements with a nonspecific eight hour outage.

LDTM,OUTAGE=8

This example evaluates fixed LDTM requirements for jobs beginning with PAY. The example uses an Outage window from January 16, 20yy at noon to January 18, 20yy at 2:00 p.m. as a reference.

LDTM,JOB=PAY*,OUTAGE=(0116yy,1200,0118yy,1400)

  LDTM,JOB=P*,OUTAGE=5
                                                          DATE=yy.080    PAGE 0001

    JOB  QUEUE CA-7 -DAY(DDD) AND TIME(HHMM)--   CPU     SCH ENTRY MSTR  JOB
    NAME  NAME JOB# DEADLINE SUB/START DUE-OUT SPEC/RUN  ID  MODE  REQ  STATUS

    P3       REQ 0792 023/1731  *NONE*  023/1731  ALL-     001 DEMD  003  LATE

   -------- ------------- SATISFACTION LEAD TIME ANALYSIS ----------------------
     JOB=P2       LKBK=yy019/22:31  LRUN=yy019/17:59  DIFF=000/04:32  *OUTAGE*
     DSN=D463BD8.BDTEST04
     DS00000004 LKBK=yy080/04:11  LRUN=yy307/11:39  DIFF=502/16:32
     CREATED BY BDTEST04

Job detail line (Starts with P3)

Contains general information about the listed job. For more information about the fields on this line, see the LQ command.

Type of requirement (JOB=)

Indicates the type of requirement.

The possible values are the following:

JOB

Job requirement

DSN

Internal data set requirement

XDSN

External data set requirement

NWK

Network requirement

Name of requirement (P2)

Name of Requirement. This is the job or network name that is a requirement. For data sets, it is the data set name that is required.

Look Back (LKBK)

Represents the point in time where CA Workload Automation SE stopped looking for the last run of the required job. Requiring job queue entry date/time minus satisfaction lead time. It is presented as YYDDD/HHMM where: YYDDD = Julian date, and hours (HH) and minutes (MM).

Last Run (LRUN)

Represents the time when the required job last completed, or the required data set was updated or created. It is presented as YYDDD/HHMM where: YYDDD = Julian date, and hours (HH) and minutes (MM). If the job has never run (or data set never created) it is presented as periods (.).

Difference (DIFF)

Provides the difference between the look back and last run times. This value represents how much the requirement "missed" being satisfied when the job came into the request queue. It is presented as DDD/HHMM where: DDD = number of days (up to 999), and hours (HH) and minutes (MM). If the required job has never run, no valid calculation can be made; therefore, the difference is presented as periods.

*OUTAGE*

Provides an outage factor indicator. If an outage is specified on the command and the requirement fits the parameters of that outage, the character string *OUTAGE* is displayed. Otherwise, it is blank.

Note: If an outage is specified on the command and LIST=ALL is NOT specified, then ONLY requirements that match the outage criteria are listed.

DS00...

Provides a data set number. If the requirement is for a data set, the CA Workload Automation SE data set number is displayed.

CREATED BY

Provides a creation job. If the requirement is for an internal data set, the name of the job that updates or creates the data set is displayed.

More information:

LQ Command