Error Messages › Audience › SARH001E

SARH001E

CA View database "xxxxxxxxxx" has detected a setting of MASTER=ALL

Reason:

A warning that MASTER is set to ALL. The CA View MASTER=ALL setting is designed to allow for initial creation of a database. MASTER=ALL indicates no restrictions, so that all users have access to administrative functions.

When a database is used in a production environment, change the SARINIT MASTER parameter to MASTER=userid. This does not limit MASTER authority to a single user. A user with master authority can assign master authority to any other user through the online DEF USER command.

Action:

Contact the administrator responsible for this CA View database. The following response is the best to this condition:

1. Determine the user ID of the master user for this database.
2. Run SARINIT with the MASTER=userid parameter. 
3. Notify this user to use the DEF USER command to assign master authority to any other users that require administrative access.

Changing the parameter does not require the CA View started task to be cycled.  As users log on to the system, the new value is used.

SARH001I

CA VIEW database "xxxxxxxx" has identified the master user as uuuuuuuu. This restricts access to administrative database functions and adheres to the best practices standards.

Reason:

Informational message.

Action:

None.

SARH003E

CA View database "xxxxxxxxxx" has detected the default setting for CLSL/FORM/DEST. This will cause every non-held sysout in the spool to be archived to CA View and deleted from JES.

Reason:

A warning that all three parameters CLSL/FORM/DEST are not set and CA View archives all classes, all forms, and all destinations. CA View archives sysouts based on CLSL, FORM, and DEST parameters. For a sysout to be archived, it must meet the selection criteria that are specified by all three of these parameters. If a parameter is not set, it defaults to all classes or forms or destinations.

Action:

Stop or Cancel the CA View started task. Notify the systems programmer. The following response is the best to this condition:

1. Run SARINIT and set either CLSL, FORM, or DEST to a non-blank value. This restricts the sysouts that CA View can archive.
2. Review any sysouts that are archived in error--these can be viewed and reprinted within CA View.  
3. Restart the CA View started task.

SARH003I

CA VIEW has verified that database "……" will selectively archive sysouts based on the following parameters: CLSL=xxx, FORM=yyy, DEST=zzz

Reason:

Informational message.

Action:

None.

SARH004E

CA View database "xxxxxxxxxx" has detected a setting of TBACKUP=NO.

Reason:

A warning that TBACKUP=NO is set. CA View database backup occurs automatically or can be manually triggered through operator commands. When NO is set, the backup cycle runs and deletes expired reports, but neither the master index nor the new report data are written to a backup tape. If a hardware or software error occurs, the database cannot be restored using CA View utilities. CA View continues processing.

Action:

Notify the systems programmer. The following response is the best to this condition:

1. Run SARINIT and set TBACKUP=YES.
2. Optionally, you can also set TBACKUP=INDEX if you are migrating reports to a Centera device.
3. Recycle the CA View started task.

SARH004I

CA VIEW has verified the setting of the TBACKUP parameter.  Setting TBACKUP=YES insures that the CA View database can be restored via CA View utilities. 

Reason:

Informational message.

Action:

None.

SARH005E

CA View database "xxxxxxxxxx" has detected a setting of ENCRYPT=ICSF, but encryption hardware (CPACF) is not installed on this machine.

Reason:

This message is informational. CA View can encrypt and decrypt reports without encryption hardware, but emulating encryption hardware is very CPU intensive.

Action:

See the CA View Health Checks section earlier in this guide for more information.

SARH005I

CA View has detected that CA View database "xxxxxxxxxx" has a setting of ENCRYPT=ICFS. This machine has the recommended hardware encryption (CPACF) support to minimize the CPU encryption overhead.

Reason:

Informational message.

Action:

None.

SARIAP01

INVALID GROUP CONTROL RECORD, ID=xxxxxxxxxxxx, GEN=nnnn and SEQ=nnnn IGNORED.

Reason:

An attempt is made to add a SYSOUT group index record with an invalid generation and sequence number. The record is ignored and processing continues.

Action:

None. This message is informational.