Reason:
The indicated volume is mounted at virtual address vaddr and ready to be copied or scanned. VMBTCPY waits for you to respond.
Action:
If you want to copy or scan this volume, enter YES. To exit VMBTCPY, enter NO.
Reason:
The volume mounted on the indicated drive has a valid standard label. If VMBTCPY overwrites this volume with the source tape, the contents of the target volume mounted on virtual address vaddr will be erased. VMBTCPY sends message 0004R.
Action:
None.
Reason:
This message follows message 0003I. VMBTCPY issues this message to make sure you really want to copy the source tape over the volume mounted on virtual address vaddr and erase the target tape's existing contents. VMBTCPY waits for you to respond.
Action:
If you want to copy the source tape over the indicated target volume, enter YES. To exit VMBTCPY, enter NO.
Reason:
VMBTCPY is starting to copy or scan the indicated tape. This may take some time; VMBTCPY issues a message, either 0007I or 0008I, when it finishes copying or scanning each tape volume. Processing continues.
Action:
None.
Reason:
The TEST option ran with no errors.
Action:
None.
Reason:
VMBTCPY successfully copied or scanned the indicated volume and encountered no errors during the copy or scan phase. VMBTCPY sends this message when the tape contains only one data set. Processing continues.
Action:
None.
Reason:
VMBTCPY successfully copied or scanned the indicated volume and encountered no errors during the copy or scan phase. VMBTCPY sends this message when the tape contains multiple data sets. Processing continues.
Action:
None.
Reason:
VMBTCPY ended normally with no errors.
Action:
None.
Reason:
VMBTCPY ended prematurely because you entered a NO response to either message 0001R or 0004R.
Action:
If you replied NO to message 0001R, mount the correct source tape. If you replied NO to message 0004R, mount the correct target tape. After mounting the correct tape, start VMBTCPY again.
Reason:
VMBTCPY encountered an invalid HDR2 tape label. Because you specified the NOVAL option, VMBTCPY does not end and copying continues. Because VMBTCPY normally obtains the density of the input tape from a field in the HDR2, you must provide the volser's density. VMBTCPY issues message 0013I.
Action:
Enter one of the valid densities specified in message 0013I.
Reason:
This message, which follows message 0012R, lists the valid densities for input tapes.
Action:
None. See message 0012R.
Reason:
You did not specify the target tape drive's virtual address (the second parameter) on the command line.
Action:
Enter the virtual address for the target tape drive and start VMBTCPY again. If you need assistance with the VMBTCPY command format or its options, enter VMBTCPY ? for help.
Reason:
You specified an extra parameter after the target tape drive virtual address. A maximum of two parameters are allowed on the command line.
Action:
Delete the extraneous parameter and start VMBTCPY again. If you need assistance with the VMBTCPY command format or its options, enter VMBTCPY ? for help.
Reason:
You specified the same virtual address on the command line for both the source and target tape drives.
Action:
Specify a virtual address for the source tape drive that is not the same as the virtual address entered for the target tape drive (or vice versa) and start VMBTCPY again.
Reason:
The indicated virtual address is not a valid address for a tape drive. The virtual address must be in the range 180-187 or 288-28F.
Action:
Specify a valid virtual address and start VMBTCPY again.
Reason:
No device is attached at the indicated address. You may have mistyped the virtual address.
Action:
Either correct the address specified or attach a tape drive at virtual address vaddr. Start VMBTCPY again.
Reason:
The device attached at the indicated virtual address is not a tape drive. You may have mistyped the virtual address.
Action:
Either correct the address or attach a tape drive at the indicated virtual address. Start VMBTCPY again.
Reason:
This tape drive has not been readied.
Action:
Mount the tape you want, ready the tape drive, and start VMBTCPY again.
Reason:
You specified an invalid option on the command line.
Action:
Correct the command line format and start VMBTCPY again. If you need assistance with the VMBTCPY command format or its options, enter VMBTCPY ? for help.
Reason:
You specified the indicated option more than once on the command line. An option can be listed only once.
Action:
Delete the duplicate options and start VMBTCPY again. If you need assistance with the VMBTCPY command format or its options, enter VMBTCPY ? for help.
Reason:
The target tape drive does not support the density of the input tape.
Action:
Attach a target tape drive that supports the indicated density.
Reason:
The source volume was written using IDRC. VMBTCPY sends message 0033E to provide additional information.
Action:
None. See message 0033E.
Reason:
The indicated tape drive does not support the IDRC feature.
Action:
Attach a drive at virtual address vaddr that supports IDRC and start VMBTCPY again.
Reason:
VMBTCPY could not find RXTAPIO MODULE on any accessed disk.
Action:
Access a disk that has a copy of RXTAPIO MODULE. This MODULE is part of the CA VM:Backup program material and is on the CA VM:Backup distribution tape.
Reason:
VMBTCPY requires a read/write A-disk to use the DISK option.
Action:
Link and access your A-disk in read/write mode and start VMBTCPY again.
Reason:
VMBTCPY encountered an invalid CA VM:Backup header label on the tape at virtual address vaddr.
Action:
Make sure the tape at the indicated virtual address was written by CA VM:Backup. If necessary, your CA VM:Backup system administrator can contact Technical Support. When the problem is corrected, start VMBTCPY again.
Reason:
VMBTCPY found two different VOL1 labels at the beginning of the tape at the indicated virtual address.
Action:
Make sure this tape was written by CA VM:Backup. If necessary, your CA VM:Backup system administrator can contact Technical Support.
Reason:
VMBTCPY found the same VOL1 label two times on the tape at the indicated virtual address. If you specified the FIX option with VMBTCPY, the utility will correct this problem and continue copying the tape. If you did not specify the FIX option, one of the following will occur:
Reason:
The output tape on this target virtual address is not capable of write operations.
Action:
Remount the tape with a write ring and start VMBTCPY again.
Reason:
The output tape at this virtual address is not long enough to hold all the data being copied from the source tape. The target tape must be at least as long as the source tape.
Action:
Use a target tape that is at least as long as the source tape and start VMBTCPY again.
Reason:
VMBTCPY unexpectedly encountered a NULL tape file instead of the trailer labels.
Action:
Make sure the tape at the indicated virtual address was written by CA VM:Backup. The CA VM:Backup system administrator can contact Technical Support. When the problem is corrected, start VMBTCPY again.
Reason:
VMBTCPY copied an invalid number of tape files from the source tape.
Action:
Make sure the indicated volume was written by CA VM:Backup. The CA VM:Backup system administrator can contact Technical Support. When the problem is corrected, start VMBTCPY again.
Reason:
VMBTCPY has reached the logical end-of-tape for the tape mounted on the target tape drive at virtual address vaddr. VMBTCPY continues copying the input tape until the physical end-of-tape is reached.
Action:
None, if the target tape is long enough to hold all of the data being copied from the input tape. Otherwise, use a target tape that is longer than the input tape. You may receive VMBTCPY message 0062E if the target tape is shorter than the input tape.
Reason:
An error occurred writing the output messages to VMBTCPY. The return code from EXECIO is code. If the return code is 113, the A-disk is full. Disk output is suspended but execution continues.
Action:
If the A-disk is full (return code = 113), clear some space on the disk. If EXECIO issues a return code other than 113, see the IBM documentation on the CMS EXECIO command for an explanation of the return code and correct the problem. Start VMBTCPY again.
Reason:
You replied to message 0001R or 0004R with an invalid response. Valid responses are either YES or NO.
Action:
Enter the appropriate valid response, either YES or NO.
Reason:
An error occurred during the indicated operation. The return code indicates the cause of the problem.
Action:
If the operation is a CMS command, see the IBM documentation for the command for an explanation of the return code. Correct the problem and start VMBTCPY again. If the operation is not a CMS command, your CA VM:Backup system administrator must contact Technical Support.
Reason:
VMBTCPY found a duplicate tape record on the input volume. If you specified the DUPFIX option with VMBTCPY, the utility corrects this problem and continues copying the tape. If you specified the DUPSCAN option with VMBTCPY, the utility reports this condition and continues processing.
Action:
None.
Reason:
VMBTCPY determined that tape records between the indicated values are missing.
Action:
Your CA VM:Backup system administrator must contact Technical Support.
Reason:
An internal error occurred in the VMBTCPY message handler.
Action:
Your CA VM:Backup system administrator must contact Technical Support.
|
Copyright © 2014 CA Technologies.
All rights reserved.
|
|