Reason:
VMBSCAN asks for the level of detail to appear in the output report. VMBSCAN waits for you to respond.
Action:
To list files and their associated minidisks, file spaces, and directories backed up on the tape, enter F. To show only the minidisks and file spaces backed up on the tape, enter D.
Reason:
The VMBSCAN utility encountered the specified error when rewinding a tape.
Action:
To determine the problem. Correct the problem and run VMBSCAN again, see the IBM documentation for the CP REWIND command.
Reason:
VMBSCAN asks that a tape be mounted on the device defined at virtual address 181. When scanning a multi-volume series, mount requests for the second and subsequent volumes in the series will specify the volser. VMBSCAN issues message 0004I and waits for you to respond.
Action:
Attach a tape drive at virtual address 181 and mount the tape. To indicate to VMBSCAN that the tape is ready, press ENTER. If you cannot locate the correct tape volume and want to end VMBSCAN processing at this point, respond to message 0004I by entering END. Reports for tapes scanned before this point will remain on your minidisk or directory accessed at filemode A.
Reason:
This message follows message 0003I. VMBSCAN waits for you to respond.
Action:
To end VMBSCAN processing at this point, enter END. See message 0003I for more information.
Reason:
VMBSCAN issues this message during initialization. The current CA VM:Backup release, genlevel, and service pack is identified and the utility begins initialization.
Action:
None.
Reason:
VMBSCAN issues this message during initialization. The currently running release was issued in year year. Initialization continues.
Action:
None.
Reason:
When you use the Reduce Tape Remounts feature, if CA VM:Backup encounters an error while backing up a minidisk, it stops backing up the minidisk. Under some circumstances CA VM:Backup leaves a partial backup of a minidisk on the tape. To indicate that this backup is not a valid backup of the minidisk, CA VM:Backup writes a cancellation record immediately following the partial backup. VMBSCAN issues message 0018I when it detects a cancellation record; this is not a problem. VMBSCAN processing continues.
Action:
None.
Reason:
VMBSCAN issues this message periodically as it processes your request.
Action:
None.
Reason:
VMBSCAN has begun to scan the tape for data. Processing continues.
Action:
None.
Reason:
The tape to be scanned was not created by CA VM:Backup. It contains either an invalid UHL1 record or an unrecognized record. The tape may have been reinitialized. VMBSCAN processing ends.
Action:
Start VMBSCAN again. Mount a valid CA VM:Backup tape when prompted for the tape to scan. The CA VM:Backup system administrator can contact Technical Support.
Reason:
The tape contains only the VOL1 and HDR1 header labels. This indicates that the tape has been reinitialized. VMBSCAN processing ends.
Action:
When a tape is reinitialized, you cannot use the VMBSCAN utility to list the contents of the tape. You cannot recover the CA VM:Backup data on the tape. Verify that you have selected the correct tape. Start the VMBSCAN utility again using a tape that has not been reinitialized.
Reason:
The VMBSCAN utility uses the READLREC routine to read data on the tape. The READLREC routine encountered an error while attempting to read a header or trailer record on the tape.
Action:
The CA VM:Backup system administrator must contact Technical Support.
Reason:
A permanent I/O error occurred while reading a tape record. This can be caused by media or hardware failure. Any data contained in the failed record cannot be read by the VMBSCAN utility. Processing continues.
Action:
If a copy of the failed tape exists, use the copy instead. If no copy exists, clean the tape drive or use another tape drive. If the problem persists, perform a service check on the tape drive subsystem. Check the output reports carefully to determine which files or minidisks may be affected by the I/O error.
Reason:
The VMBSCAN utility uses the READLREC routine to read data on the tape. The READLREC routine encountered an error while attempting to read tape records on the tape.
Action:
The CA VM:Backup system administrator must contact Technical Support.
Reason:
This is the volser information contained in the header label on the tape. Processing continues.
Action:
None.
Reason:
This is the name of the data set currently being processed. Processing continues.
Action:
None.
Reason:
The volume sequence number indicates the relative position of a tape within a multivolume series. Processing continues.
Action:
None.
Reason:
This is the data set sequence number of the data set currently being processed. The data set sequence number indicates the relative position of a data set on a tape. Processing continues.
Action:
None.
Reason:
This is the date when the data set being processed was created. Processing continues.
Action:
None.
Reason:
This is the date on which the data set being processed expires. Processing continues.
Action:
None.
Reason:
This message displays the previous volume in a multivolume series. Processing continues.
Action:
None.
Reason:
This message displays the volsers of the copies of this tape. Processing continues.
Action:
None.
Reason:
VMBSCAN finished processing the indicated data set on this tape. Processing continues.
Action:
None.
Reason:
VMBSCAN finished processing the indicated tape. VMBSCAN issues message 0003I to ask you to mount the next tape in the multivolume series.
Action:
None. See message 0003I.
Reason:
VMBRITS finished processing the indicated data set on this tape. Processing continues.
Action:
None.
Reason:
VMBRITS finished processing the indicated tape and issues message 0003I asking you to mount the next tape in the multivolume series.
Action:
Mount the tape volume requested by message 0003I.
Reason:
This message indicates the next tape in a multivolume series. Processing continues.
Action:
None.
Reason:
VMBSCAN finished processing the indicated data set on this tape. The data set is continued on the next tape in this multivolume series. VMBSCAN issues message 0003I to ask you to mount the next tape in the series.
Action:
None. See message 0003I.
Reason:
VMBSCAN has written information about the data contained on the tape to the indicated file on your minidisk or directory accessed at filemode A. If tapes remain to be processed in a multivolume series, VMBRITS asks you to mount the next tape in the series with message 0003I. If all tapes have been processed, VMBSCAN ends.
Action:
None, unless message 0003I is issued. If it is, respond appropriately.
Reason:
The VMBSCAN utility encountered a severe error. For an explanation of the error. VMBSCAN processing ends, see the previous message.
Action:
To determine how to correct the problem, see the response of the previous message.
Reason:
During a VMBSCAN job, an error occurred while writing the report to the A-disk. The return code from EXECIO is code. VMBSCAN ends with a return code of 100.
Action:
To receive a complete report, either clear some space on the A-disk or define a larger minidisk. Start VMBSCAN again.
|
Copyright © 2014 CA Technologies.
All rights reserved.
|
|