Installation Worksheet

Installation Worksheet

The pre-installation worksheets are designed to simplify modifying the JCL supplied at installation. The parameter values are supplied for your convenience.

SMP/E Installation Job Procedures

The following parameters are required for the SMP/E installation job procedures:

1. Job card information for card one.

   Default: ‘JOBCARD1’

2. Job card information for card two.

   Default = 'JOBCARD2’

3. Job card information for card three.

   Default = 'JOBCARD3'

4. Job card information for card four.

   Default = 'JOBCARD4’

5. Volume information for the product and SMP/E target and distribution datasets. Use either the VOL=SER or the SMS VOLINFO statement when editing the ISREDIT macro.

   Default = 'VOLINFO’

6. Volume information for the CSI VSAM data set. Use either the VOL=SER or the SMS CSIVOLINFO statement when editing the ISREDIT macro.

   Default = 'CSIVOLINF'

7. High level qualifier for the GLOBAL ZONE.

   Default = 'GLOBALHLQ'

8. SMP/E High level qualifier for the CAIT0 TARGET ZONE.

   Default = 'CAIT0HLQ'

9. Product dataset high level qualifier.

   Default = 'PRODHLQ'

10. (Required if installing from DASD) High level qualifier for the datasets that were unzipped.

    Default = 'DASDHLQ'

11. High level qualifier used for the SAMPJCL data set.

    Default = 'SAMPHLQ'

12. SMS Output data class.

    Default = ‘DCLAS'

13. SMS Output storage class.

    Default = ‘SCLAS'

14. SMS Output management class.

    Default = 'MCLAS’

15. Generic device type or symbolic group name for magnetic tape.

    Default = 'TAPEUNIT’

16. Disk unit name

    Default = 'DISKUNIT'

17. High level qualifier for SMP/E temporary files.

    Default = 'SMPETEMP'

18. Data set fixed block size.

    Default = TGTBLKSZ’

19. Target Zone name.

    Default = 'ZNCAIT0'

20. Distribution Zone name.

    Default = 'ZNCAID0'

21. The IBM CICS/TS target load library.

    Default = ‘SDFHLOAD'

Post-SMP/E Job Procedures

The following parameters are required for all of the post-SMP/E job (custom, new, and upgrade) procedures:

1. The high level qualifier for the SMP/E target and distribution data sets.

   Default = 'PRODHLQ'

2. The high level qualifier for the Custom libraries.

   Default = 'CAI.CHLQ'

3. The high level qualifier for the CA IPC datasets.

   Default = 'CAI.HLQ'

4. The high-level qualifier for the previous version CA IPC data sets.

   Default = 'CAI.PHLQ'

5. The unit name for the temporary data sets.

   Default = 'SYSDA'

6. What DASD volume serial name is to be used for the CA IPC INSTJHCL dataset.

   Default = 'DASD01'

7. What DASD type is the VQVOL1 volume? For example, "SYSDA,3390,3390"

   Default = '3390'

8. What DASD volume serial name is to be used for the CA IPC custom Libraries.

   Default = 'DASD02'

9. What DASD type is the VQVOL2 volume? For example, "SYSDA,3380,3390"

   Default = '3390'

10. What DASD volume serial name is to be used for the new CA IPC VLS files?

    Default = 'DASD04'

11. What DASD type is the VQVOL4 volume? For example, 'SYSDA,3380,3390'

    Default = '3390'

12. What tis the data set name of the CICS CSD?

    Default = 'CICS.DFHCSD'

13. What is the group list name for CICS?

    Default = 'CICSGRPL'

14. What is the data set name for the CICS/TS target macro library?

    Default = 'CICS.SDFHMAC'

15. What is the data set name for the CICS/TS target load library?

    Default = 'CICS.SDFHLOAD'

16. What is the suffix used for the CICS/TS table assemblies?

    Default = 'VQSFX'

17. What is the name of the Linkage Editor module for link-editing?

    Default = 'IEWL'

18. What is the name of the Assembler module?

    Default = 'ASMA90'

19. What is the name of the utility program used to copy data sets?

    Default = 'IEBCOPY'