Previous Topic: Start the XCOMPLEX Admin Server (Deprecated)

Next Topic: Perform a Direct File Transfer (TYPE=EXECUTE)

Configuring and Customizing Your Product › Verify the Installation › Start the XCOMPLEX Worker Server (Deprecated)

Start the XCOMPLEX Worker Server (Deprecated)

Important! The existing XCOMPLEX facility has been deprecated. The following information is provided for backward compatibility only. All new installations should use the new PLEXQ implementation. Existing XCOMPLEX users should migrate to the PLEXQ infrastructure for their XCOMPLEX functionality.

Normally the XCOMPLEX Admin Server is brought up first, then the XCOMPLEX Worker Servers, although this is not a requirement.

To start an XCOMPLEX Worker Server

Enter one of the following commands on the z/OS console (or any TSO/ISPF or NETVIEW session) where the user is authorized to invoke z/OS system commands:

Several informational messages are displayed when CA XCOM Data Transport is started, as shown in the following excerpt:

XCOMM0991I XCOMPLEX         = XCOMPLEX_BAS                                         
XCOMM0008I XBAS31W  ACB OPENED SUCCESSFULLY                                        
XCOMM0009I COMPILED UNDER VTAM V6 R1 M9 - EXECUTING UNDER VTAM V6 R1 M9            
           5695-11701-190                                                          
XCOMM0763I DEFAULT TABLE BASWK115 LOADED. GENERATED 03/17/08 AT 21.51              
XCOMM0027I ESTAE ROUTINE HAS BEEN ESTABLISHED                                      
XCOMM0037I PSO SUBTASK ATTACHED SUCCESSFULLY                                       
XCOMM0330I PRIMARY SUBSYSTEM IS JES2                                               
XCOMM1000I STARTING CROSS-SYSTEM COUPLING FACILITY SERVICE TASK                    
XCOMM0056I               CA XCOM(TM) r11.6 (GEN LEVEL 1203 SP00) IS UP AND 
           ACCEPTING LOGONS                                                        
XCOMM0056I ON CPU 2097 SERIAL # 0CE000 IN 31-BIT MODE MVS SP7.0.9                  
XCOMM1068I CROSS-COUPLING FACILITY LISTENER TASK STARTING                          
XCOMM0803I STARTING XCOM TCP/IP LISTENER                                           
XCOMM0788I XCOM TCP/IP LISTENER ACTIVE ON PORT 06653, STACK ***ALL**               
XCOMM0819I TCP/IP FUNCTION GETHOSTID RETURNS ADDRESS 141.202.65.31                 
XCOMM0559I XBAS31A  ENABLED  SUCCESSFULLY                                          
XCOMM0559I XCOMMVS2 ENABLED  SUCCESSFULLY                                          
XCOMM0559I BASLIST  ENABLED  SUCCESSFULLY                                          
XCOMM1019I XCF CONNECT STR=XCOMPLEX_BAS    , CONN=XBAS31W , RC=00000000,           
           RSN=00000000, DISP=OLD                                                  
XCOMM1020I MAXIMUM SERVERS SUPPORTED=00000061                                      
XCOMM1054I MAXIMUM LIST ENTRIES SUPPORTED=00001392                                 
XCOMM1017I XCF READING MASTER ENTRY FROM LIST #0000                                
XCOMM1013I XCF REQ=READ             RC=00000000 REASON=00000000 LIST=0000          
           ENTRY=XCOMPLEX_BAS                                                      
XCOMM1022I LOCATING SERVER ENTRY IN LIST #0000                                     
XCOMM1026I UPDATING MASTER ENTRY IN LIST #0000                                     
XCOMM1028I ADDING SERVER ENTRY FOR NODE (XBAS31W ) WHICH IS USING LIST #0002       
XCOMM0454I OPERLIM EXCEEDS XCF MAX ENTRIES. OPERLIM REDUCED TO VALUE IN 
           XCOMM1054I MESSAGE                                                      
XCOMM1005I XCOMPLEX SERVICES ENABLED FOR NODE (XBAS31W )