General Considerations for All Users

Starting Your Product › How to Configure Without CA CSM › Step 13: (Optional) Replace or Modify User Exits › General Considerations for All Users

General Considerations for All Users

The following table lists the user exits and the CAIOPTN members that you can use to install them.

Note: For more information about user exits, see the chapter "User Exits" in the Programming Guide.

User Exit	CVDEJCL Member	CVDEJCL Non-SMP	Function
SARACFUX	BRMSACFX	BRMJACFX	ACIF archival task exit
SARACTUX	BRMSACTX	BRMJACTX	Job accounting
SARARAUX	BRMSARAX	BRMJARAX	Automatic report archival
SARATHUX	BRMSATHX	BRMJATHX	Authorization
SARBKTUX	BRMSBKTX	BRMJBKTX	Backup cycle
SARDSTUX	BRMSDSTX	BRMJDSTX	Reprint destinations
SARD00UX	BRMSD00X	BRMJD00X	Migrate Cycle exit
SARD03UX	BRMSD03X	BRMJD03X	Secondary Storage Drive exit
SARD05UX	BRMSD05X	BRMJD05X	Secondary Storage Drive exit
SAREASUX	BRMSEASX	BRMJEASX	EAS for tape and robotics exit
SARFVCUX	BRMSFVCX	BRMJFVCX	View collector archival task exit
SARJS2UX	BRMSJS2X	BRMJJS2X	JES control block mapping
SARMFPUX	BRMSMFPX	BRMJMFPX	Microfiche
SAROMSUX	BRMSOMSX	BRMJOMSX	Online management system
SARPACUX	BRMSPACX	BRMJPACX	SARPAC tape consolidation
SARPAMUX	BRMSPAMX	BRMJPAMX	SARPAM Service Routine exit
SARPRFUX	BRMSPRFX	BRMJPRFX	User profile
SARPRTUX	BRMSPRTX	BRMJPRTX	Print
SARSECUX	BRMSSECX	BRMJSECX	Security
SARSMFUX	BRMSSMFX	BRMJSMFX	SMF processing
SARSPFUX	BRMSSPFX	BRMJSPFX	Selection list formatting
SARSRQUX	BRMSSRQX	BRMJSRQX	Selection request
SARSTCUX	BRMSSTCX	BRMJSTCX	Archival task
SARSUBUX	BRMSSUBX	BRMJSUBX	Job submission
SARTPOUX	BRMSTPOX	BRMJTPOX	Tape creation VOLSER exit
SARUNLUX	BRMSUNLX	BRMJUNLX	Selective Unload User exit
SARUSxUX	BRMSUSxX	BRMJUSxX	User ID determination
SARXCTUX	BRMSXCTX	BRMJXCTX	Exceptional condition checking

Note: Sample JCL is provided to assist with the installation of most CA View user exits in two formats. One sample format provides JCL for SMP/E-controlled USERMOD installation, and one sample format provides JCL to install outside of SMP.

The non-SMP/E samples have been provided in this release to help facilitate improved management of multiple sets of target libraries that have been deployed on more than a single LPAR and have different configuration criteria. To safely manage user exits outside of SMP/E, link the exits into a separate, independent load library that can be link-listed or concatenated before the CA View product load library. We recommend that you test the product before customizing exits.

For more information about User Exits, see the Programming Guide.