Converting SMU Control Statements to CA Top Secret › Conversion Utilities Messages

Conversion Utilities Messages

Unable to locate SAF IVT

Reason:

A critical CA SAF control block could not be located. An improper installation of the security product or corruption of common storage may cause this. The utility terminates.

Action:

Contact CA Technical Support.

Module:

TSSISMU1, TSSISMU2, TSSISMU3, TSSISMU4, TSSISMU5

Error opening the SMU input file

Reason:

The utility encountered an error finding or opening the SMU input file. The utility terminates.

Action:

Make sure that the SMU DD statement exists and points to a sequential data set, with an LRECL of 80, containing the SMU security statements to be processed.

Module:

TSSISMU1, TSSISMU2, TSSISMU3, TSSISMU4, TSSISMU5

Error opening the TSSCMDS output file

Reason:

The utility encountered an error finding or opening the TSSCMDS output file. The utility terminates.

Action:

Make sure that the TSSCMDS DD statement exists and points to a sequential data set, with an LRECL of 80, which is used to contain the output commands from the utility.

Module:

TSSISMU1, TSSISMU2, TSSISMU3, TSSISMU4

Error opening the TSSCFILE input file

Reason:

The utility encountered an error finding or opening the TSSCFILE input file. The utility terminates.

Action:

Make sure that the TSSCFILE DD statement points to a sequential data set, with an LRECL of 300, containing the CFILE input data.

Module:

TSSISMU2, TSSISMU3, TSSISMU4

Error opening the REPORT output file

Reason:

The utility encountered an error opening the REPORT input file. The utility terminates.

Action:

Make sure that the REPORT DD statement points to a sequential data set, with an LRECL of 80.

Module:

TSSISMU1, TSSISMU3, TSSISMU5

Error opening the STG1IN input file

Reason:

The utility encountered an error finding or opening the STG1IN input file. The utility terminates.

Action:

Make sure that the STG1IN DD statement points to a sequential data set, with an LRECL of 80, containing the IMS system definition statements to be processed.

Module:

TSSISMU1, TSSISMU3

Error opening the STG1OUT output file

Reason:

The utility encountered an error finding or opening the STG1OUT output file. The utility terminates.

Action:

Make sure that the STG1OUT DD statement exists and points to a sequential data set, with an LRECL of 80, which will contain the updated IMS system definition statements.

Module:

TSSISMU1, TSSISMU3

Invalid value in the PARM='department,facility' input parameter

Invalid value in the PARM='msca, owner,facility' input parameter

Invalid value in the PARM=facility input parameter

Invalid value in the PARM='ATS|USER,owner,facility,dept' input parameter

Reason:

One of the values specified in the PARM= parameter is missing, or the value specified was longer than eight characters. The utility terminates.

Action:

Specify valid values in the PARM= parameter in the utility JCL.

Module:

TSSISMU1, TSSISMU2, TSSISMU3, TSSISMU4

Insufficient storage for execution

Reason:

The utility was unable to obtain sufficient storage for internal work areas. The utility terminates.

Action:

Increase the region available for the utility execution.

Module:

TSSISMU1, TSSISMU2, TSSISMU3, TSSISMU4

Invalid SMU input - record nn

Reason:

The utility encountered a syntax error processing a SMU input record. The relative record number for the SMU record is nn. The utility terminates.

Action:

Edit the SMU input and determine the syntax error in record number nn. Some of the reasons for this message are a command name that is longer than ten characters or a transaction name longer than eight characters. Correct the error.

Module:

TSSISMU1, TSSISMU2, TSSISMU3, TSSISMU4, TSSISMU5

There were no AOI transactions processed.

Reason:

This message can occur in the TSSISMU1 AOI=TRAN report or the TSSISMU3 AOI=YES report. The message is issued when the conversion utility did not find any valid CTRANS statements in the SMU security definitions. Since there are no transactions that issue AOI commands, no transaction definitions in the IMS system definition (stage 1) need to be modified.

Action:

This is an informational message. No action is required.

Module:

TSSISMU1, TSSISMU3