Installing Your Product Using Pax ESD or DVD › Prepare the SMP/E Environment for a Pax Installation

Prepare the SMP/E Environment for a Pax Installation

The following steps describe the process to install products using native SMP/E JCL:

1. Download external HOLDDATA.
2. Allocate product data sets and SMP/E data sets.
3. Create an SMP/E environment.
4. Receive base functions and HOLDDATA.
5. Download and RECEIVE PTFs from http://ca.com/support.
6. Run an SMP/E APPLY CHECK operation.
7. Apply base functions using SELECT GROUPEXTEND.
8. Run an SMP/E ACCEPT CHECK operation.
9. Accept base functions using SELECT GROUPEXTEND.
10. Configure the product according to your site requirements.

The members that are used in this procedure prepare the data sets, initialize the zones, and create the DDDEFs for your product.

Establishing a hierarchical file system (HFS) may be required as part of the product installation or required as a feature of the product.

For information about the members, see the comments in the JCL.

Follow these steps:

1. Customize the macro SPLSEDIT with your site-specific information and then copy the macro to your SYSPROC location. Replace the rightmost parameters for each ISREDIT CHANGE command. Each time you edit an installation member, type SPLSEDIT on the command line, and press Enter to replace the defaults with your specifications.

   The macro is ready to customize the yourHLQ.SAMPJCL members.

   Note: Set the DASD HLQ to the same value specified for yourHLQ within the JCL that is used to unzip the pax file.

   Note: The following steps include instructions to execute the SPLSEDIT macro each time you open a new SAMPJCL member. To edit all SAMPJCL members simultaneously, read and follow the instructions in the SPLAREAD member, and submit the SPLEDALL member.

2. Open the SAMPJCL member SPL1HOLD in an edit session and execute the SPLSEDIT macro from the command line.

   SPL1HOLD is customized.

3. Submit SPL1HOLD.

   This job downloads the error and FIXCAT HOLDDATA from http://ca.com/support.

4. Open the SAMPJCL member SPL2ALL in an edit session and execute the SPLSEDIT macro from the command line.

   SPL2ALL is customized.

5. Submit SPL2ALL.

   This job produces the following results:

   • The target and distribution data sets for your product are created.
   • Unique SMPLTS, SMPMTS, SMPSCDS, and SMPSTS data sets for this target zone are created.
6. If your product requires HFS or if you want to install a feature of the product that requires HFS, complete the following substeps:

   If you do not use ZFS or HFS, skip this step and proceed to the next step.

   1. Open the SAMPJCL member BQ42ALLU in an edit session and execute the SPLSEDIT macro from the command line.

      Note: All instances of BQ4 in this section indicate a three-character component code based on the FMID.

      BQ42ALLU is customized.

   2. Submit BQ42ALLU.

      This job allocates your HFS data sets.

   3. Open the SAMPJCL member BQ43MKD in an edit session and execute the SPLSEDIT macro from the command line.

      BQ43MKD is customized.

   4. Submit BQ43MKD.

      This job creates all directories and mounts the file system.

7. Open the SAMPJCL member SPL3CSI in an edit session and execute the SPLSEDIT macro from the command line.

   SPL3CSI is customized.

8. Submit SPL3CSI.

   This job produces the following results:

   • The CSI data set is defined.
   • The SMPPTS and SMPLOG data sets are allocated.
   • The global, target, and distribution zones are initialized.
   • The DDDEF entries for your product are created.
   • The DDDEFs for the required SMP/E data sets are created.
9. If your product requires HFS or if you want to install a feature of the product that requires HFS, complete the following substeps:

   If you do not use ZFS or HFS, skip this step.

   1. Open the SAMPJCL member BQ43CSIU in an edit session and execute the SPLSEDIT macro from the command line.

      BQ43CSIU is customized.

   2. Submit BQ43CSIU.

      This job customizes the CSI by adding the DDDEFs associated with the directory.