3. REPORTS › 3.1 MICF Inquiries › 3.1.5 Financial Analysis Inquiries › 3.1.5.3 CICCMS: Monthly CICS Cost

3.1.5.3 CICCMS: Monthly CICS Cost

The Monthly CICS Cost graph shows the percentage of monthly
CICS cost associated with each system (SYSID) or data center
(group of SYSIDs) in the enterprise.

REPORT FORMAT:

This inquiry produces a pie chart showing the percentage of
processing cost associated with each system or data center.
When there are more than 10 SYSIDs or grouping of SYSIDs, all
systems which consumed less than 5% of the total cost will be
grouped together.  When there is only one SYSID present, the
pie slices will show the CICSIDs values.  The output of this
inquiry is in color graphic format.  However, you can produce
the same chart in printer graphic format by executing the
MICF inquiry CICPMU.


INQUIRY ID:

     CICCMU (color graphic format)

DATA SOURCE (file/timespan):

     CICCAU01 in the MONTHS timespan.



     If the CICCAU (CICS Application Unit Activity) file is
     not active, the CICCSU (CICS User Activity) file will be
     used for reporting.  The variable CICACT2 will be used
     in place of the variable CICAPU.

DATA ELEMENTS USED:

     CAUCOST  - Processing Charges
     CICAPU   - CICS Application Unit ID
     CICSID   - CICS System Identifier
     MONTH    - Month of Year
     YEAR     - Year of Century
     ZONE     - Time Zone
     SYSID    - System Identifier

   CALCULATIONS:

     None

EXECUTION-TIME PARAMETERS:

     UNIT   - Select one or more CA MICS data base units by
              entering the data base IDs.  Enter multiple IDs
              with a blank following each ID value.

     CYCLE  - Optionally, define CA MICS input file cycle
              range.

              For this inquiry, the default is the 01 cycle.


     SYSID  - Optionally, specify the SYSID to be reported.
              If no value is specified, the value *ALL is
              used. It causes all SYSIDs found in input to
              be summarized together.


     CICSID - Optionally, specify the CICSID to be reported.
              If no value is specified, the value *ALL is
              used which causes all CICSIDs found in input to
              be summarized together.

     CENTER - Optionally, specify the CENTER to be reported.
              If no value is specified, the value *ALL is
              used which causes all CENTERs found in input to
              be summarized together.  CENTER is a logical
              grouping of SYSIDs which you assign in the
              global exit %GCNTR.  If this exit is not
              defined, CENTER is set to the value of SYSID.

     MONTH  - Optionally, enter the month (mm) and year (yy)
              to be reported.

     ZONE   - Optionally, select one or more CA MICS time
              zones.  Valid values are numbers 1 through 9.

     DEVICE - Optionally, override the default colors and
              patterns used by specifying a different device
              type.  The default is TERMINAL.  Because the
              code for color graphics is not generated by
              MICF, the device parameter you specified in
              MICF is not applicable here.

     FOOTNOTE-Optionally, specify whether or not the MICF
              inquiry ID should be displayed as a footnote on
              the graph.  The default value is NO.

     FILE ID- Optionally, select the CICCSU file as input
              when the CICCAU file is active.  If you specify
              this parameter, then you must also specify the
              next parameter to indicate which account code
              (CICACT1-CICACT9) identifies your CICS
              application.

     CICAPU - Optionally, replace CICAPU with any of the
              CICACTx data elements, where x is 1 to 9.  This
              parameter must be specified in conjunction with
              FILE ID.

USER EXITS:

     If the MICF execution-time parameters are insufficient
     to select the data you need, you can invoke one of the
     following global exits to further manipulate the input
     file.  Additionally, you can override the global exit
     definitions in MICF using independent source statements.
     For detailed information on coding the exits, refer to
     Section 3.2 of this guide.

     The global exits are defined by macros in the source
     module CICRPTGL in sharedprefix.MICS.SOURCE.  The
     following exits are available to this inquiry:

     %GAPPL  - Define your CICS application based on any
               variable in the input file.  The default is
               CICAPU.

     %GCIC  -  Select CICSIDs for report.

     %GCNTR -  Assign value to the variable CENTER which
               defines the logical grouping of SYSIDs.
               CENTER is set to SYSID by default.

     %GSYS  -  Select SYSIDs for report.