Previous Topic: Application System RegenerationNext Topic: Business System Regeneration

Intelligent Regeneration › Application System Regeneration › Access the Regeneration Menu

Access the Regeneration Menu

Follow these steps:

  1. Display the Application System Regeneration panel. 
                            Application System Regeneration
 COMMAND ===>

  Select one of the options below, then press enter.

  _ 1. Construction change impact report
    2. Regenerate application system
    3. Regeneration impact analysis report
    4. Construction regeneration report
    

       F1=Help  F3=Exit  F12=Cancel
  2. Type 2 for Regenerate application system and press Enter. 
                          Regenerate Application System
  COMMAND ===>

  Type a model name or request Prompt for list selection. Select the business
  system scope. If the business system scope is one business system, type a
  business system name or request Prompt for list selection. Select the load
  module scope, then press enter.

    Model name . . . . . .   GEN SAMPLE MODEL________________  +

    Business System scope    / All business systems
                             . One

    Business System name     ________________________________  +

    Load Module scope  . .   / All load modules
                             . Multiple
 
    

      F1=Help  F3=Exit  F4=Prompt  F12=Cancel
  3. Type the Host Encyclopedia name of the model or use the Tab key to move the cursor to the field and press the Prompt key for a list of valid choices. Select a model name from the list by typing any character except a period (.) or a space character next to the name, and press Enter.
    1. Scope the business system by placing a slash character (/) opposite the option to enable. Place a period character (.) opposite the option to disable.
    2. Type a business system name only if you are regenerating a single business system. To regenerate all business systems, do not type a name in this blank.

      You can also use the Tab key to move the cursor to the field and press the Prompt key for a list of valid choices. Select a business system name from the list by typing any character except a period (.) or a space character next to the name and press Enter.

    3. Scope the load module by placing a slash character (/) opposite the option to enable. Place a period character (.) opposite the option you disable.
  4. Press Enter. 
                                 Regeneration Options
 COMMAND ===>

  To limit regeneration by date, type a beginning and/or ending date.
  To limit regeneration to a specific user, type the TSO user ID.
  To limit regeneration to a specific group, type the Group ID.
  To ignore Target Environment Parameter changes, select Yes.
  To mark and record components requiring regeneration, select Yes.
 
  Begin date  . . . . . . . . . . . . . . . . .   0___ - 0_ - 0_ YYYY-MM-DD or 0
  End   date  . . . . . . . . . . . . . . . . .   0___ - 0_ - 0_ YYYY-MM-DD or 0
  User ID . . . . . . . . . . . . . . . . . . .   ________ TSO user ID
  Group ID  . . . . . . . . . . . . . . . . . .   ________ Group ID

  Ignore Target Environment Parameter Changes . . . . .    / Yes
                                                           . No
  Mark & record components requiring regeneration . . .    / Yes
                                                           . No

  Limiting regeneration to a particular user/group or by date may cause
  inconsistencies at generation/installation time.  Some components that
  are not within these limits may need to be regenerated.

  F1=Help  F3=Exit  F12=Cancel
  5. Specify required limitations, if any, on the scope of the regeneration about beginning or ending dates, TSO user ID, Group ID, and rejection of the target environment changes.

    Limiting regeneration to a particular user/group or by date cause inconsistencies during generation and installation. Some components that are not within the specified limitations require regeneration.

  6. To retain the results of the analysis, select Yes for the Mark & record components requiring generation option. This option is useful if no or minimal changes had been made to a model since the last regeneration session but components had been marked for regeneration in that earlier session and the user chose not to regenerate them. If this option is set to No, the next intelligent regeneration operation must extract all of the aggregate changes that are made to the model since the earliest generation date for the set of components. This would degrade performance.
  7. When you select No for the Ignore Target Environment Parameter Changes option, Intelligent Regeneration can detect changes to the business system target environment parameters and RI Trigger Target Environment parameters Dynamically Link RI Triggers option and RI Trigger Name. Intelligent Regeneration cannot detect other RI Trigger Target Environment parameter changes, such as DBMS type for RI triggers. If the DBMS type has changed for RI triggers, generate and install the RI triggers using the Application System Construction (regular generation) tools.
  8. Press Enter. 
                                   Regeneration
 COMMAND ===>

  Select one of the options below, then press enter.

  _ 1. Business system
    2. Load module
    3. Action block
    4. Screen
    5. Referential integrity triggers

  F1=Help  F3=Exit  F12=Cancel
  9. Select the appropriate level of detail for the regeneration.