Using the Library Conversion Utilities › The PROC Definition

The PROC Definition

This section describes the PROC definition portion of conversion job stream and the variables for which you need to provide values before submitting the job.

The following JCL shows the PROC definition portion of the conversion job stream:

// (JOBCARD)
//*
//*********************************************************************
//*  THIS JCL MUST BE TAILORED PRIOR TO SUBMITTING THIS JOB     *
//*                                  *
//*   1. CHANGE TDISK TO A UNIT NAME FOR WORK DASD ──       *
//*     FOR BEST PERFORMANCE, SPECIFY A VIO DEVICE        *
//*                                  *
//*     CHANGE iprfx.iqual TO YOUR CA Endevor SCM INSTALL PREFIX   *
//*                                  *
//*                                  *
//*   2. CHANGE PDISK TO A UNIT NAME FOR DATA SETS WHICH     *
//*     WILL CONTAIN CA Endevor SCM LOAD SCL STATEMENTS USED FOR   *
//*     INPUT INTO THE CA Endevor SCM LOAD UTILITY JOB        *
//*                                  *
//*     CHANGE PVOLSER (OR REMOVE VOL=SER=PVOLSER) TO A VALID  *
//*     VOLUME SERIAL NUMBER                   *
//*                                  *
//*     CHANGE UPRFX.UQUAL TO THE APPROPRIATE INDEX LEVELS    *
//*     AT YOUR SITE                       *
//*                                  *
//*   3. TAILOR THE THREE LINES THAT CONTAIN THE TEXT       *
//*     'DSN1' 'DSN2' 'DSN3' TO REFLECT THE ACTUAL LIBRARY    *
//*      NAMES FROM WHICH YOU ARE CONVERTING.          *
//*                                  *
//*                                  *
//*   4. ON THE ASSIGN STATEMENT USED IN STEP TWO, SPECIFY    *
//*     THE ACTUAL ENVIRONMENT, SYSTEM, SUBSYSTEM, STAGE ID   *
//*     AND CCID VALUES THAT ARE TO BE USED TO CONSTRUCT THE   *
//*     LOAD UTILITY SCL.                    *
//*                                  *

//*********************************************************************
//ANALYZE PROC
//*
//C1BM7000 EXEC PGM=NBURC1,PARM=C1BM7000
//     DYNAMNBR=1500,REGION=4096K
//*
//CONLIB  DD DSN=iprfx.iqual.CSIQLOAD,DISP=SHR
//*
//C1TPDD01 DD UNIT=tdisk,SPACE=(CYL,3),
//      DCB=(RECFM=VB,LRECL=260,BLKSIZE=6160)
//C1TPDD02 DD UNIT=tdisk,SPACE=(CYL,5),
//      DCB=(RECFM=VB,LRECL=260,BLKSIZE=6160)
//C1TPLSIN DD UNIT=tdisk,SPACE=(CYL,3),
//      DCB=(RECFM=FB,LRECL=80,BLKSIZE=6160)
//C1TPLSOU DD UNIT=tdisk,SPACE=(CYL,5)
//C1PLMSGS DD SYSOUT=*
//*********************************************************************
//* OUTPUT DATA SETS                         *
//*********************************************************************
//C1MSGS1 DD SYSOUT=*
//C1SUMARY DD SYSOUT=*
//C1PRINT DD SYSOUT=*,DCB=(RECFM=FBA,LRECL=121,BLKSIZE=6171)
//SYSABEND DD SYSOUT=*
//SYSOUT  DD SYSOUT=*
//BSTERR  DD SYSOUT=*
//     PEND

Tailor this JCL by providing values for all occurrences of the following variables:

iprfx

Highest-level qualifier used to assign data set names for installation files at your site.

iqual

Second-level qualifier used to assign data set names for installation files at your site.

tdisk

Unit name for temporary disk data sets.