Error Codes and Messages › CONRELE Messages

CONRELE Messages

This section lists error messages issued during CONRELE processing along with possible causes and corrective actions to take in error situations.

CONRELE E001

INVALID COMMAND SYNTAX RECEIVED.

Reason:

An error occurred in the input syntax parsing.

Action:

Correct the syntax errors and reenter the command.

CONRELE E002

ELEMENT WAS NOT FOUND.

Reason:

The Element was not included with the RELATE ELEMENT command.

Action:

Add the Element to the RELATE ELEMENT command and reenter the command.

CONRELE E003

INPUT OR OUTPUT MUST BE SPECIFIED FOR ELEMENT, BUT NOT BOTH.

Reason:

Both the input component and the output component were specified with the RELATE ELEMENT command.

Action:

Remove either the input component or the output component from the RELATE ELEMENT command and reenter the command.

CONRELE E004

INPUT OR OUTPUT MUST BE SPECIFIED FOR ELEMENT.

Reason:

An input clause or an output clause was not specified with the RELATE ELEMENT command.

Action:

Add an input clause or an output clause to the RELATE ELEMENT command and reenter the command.

CONRELE E005

ERROR OCCURRED ON ELEMENT. ENV: Environment_name SYSTEM: System_name SUBSYSTEM: Subsystem_name NAME: Element_name TYPE: type_name STG: Stage_id.

Reason:

This message indicates the Element (associated with the RELATE ELEMENT command) where the error occurred. This message is followed by another message indicating the type of error.

Action:

Read the following message and respond accordingly.

CONRELE E006

DATA SET NOT SPECIFIED. <- ERROR ON RELATE MEMBER COMMAND.

Reason:

The data set was not specified with the RELATE MEMBER command.

Action:

Add the data set to the RELATE MEMBER command and reenter the command.

CONRELE E007

INPUT OR OUTPUT MUST BE SPECIFIED FOR MEMBER, BUT NOT BOTH.

Reason:

Both the input clause and the output clause were specified with the RELATE MEMBER command.

Action:

Remove either the input clause or the output clause from the RELATE MEMBER command and reenter the command.

CONRELE E008

INPUT OR OUTPUT MUST BE SPECIFIED FOR MEMBER.

Reason:

An input clause or an output clause must be specified with the RELATE MEMBER command.

Action:

Specify an input clause or an output clause with the RELATE MEMBER command and reenter the command.

CONRELE E009

UNABLE TO ALLOCATE DATA SET, RC = return_code

Reason:

This message indicates that the data set specified with the RELATE MEMBER command could not be allocated.

Action:

Check the spelling of the data set name and verify that the data set exists.

CONRELE E010

DATA SET FAILED VALIDATION, RC = return_code

Reason:

This message indicates that the data set specified with the RELATE MEMBER command could not be validated.

Action:

Check the spelling of the data set name and verify that the data set exists.

CONRELE E011

UNABLE TO OPEN DATA SET, RC = return_code

Reason:

This message indicates that the data set specified with the RELATE MEMBER command could not be opened.

Action:

Check the spelling of the data set name and verify that the data set exists.

CONRELE E012

UNABLE TO OBTAIN FOOTPRINT, RC = return_code

Reason:

This message indicates that the footprint for the member specified with the RELATE MEMBER command could not be obtained.

Action:

Verify that a footprint exists for the data set member and run a processor to create a footprint if a footprint does not exist.

CONRELE E013

ERROR OCCURRED ON MEMBER. DATA SET: data set_name MEMBER: member_name

Reason:

This message indicates the data set and the member where the error occured. See the following message for the cause.

Action:

Read the following message and respond accordingly.

CONRELE E014

STORAGE REQUEST FOR OBJECT FAILED: RC = return_code

Reason:

The storage request failed because of insufficient storage.

Action:

Note the return code and contact your administrator.

CONRELE E015

NO OBJECT DATA SPECIFIED FOR RELATE OBJECT COMMAND.

Reason:

The object data was not specified with the RELATE OBJECT command.

Action:

Add the data clause and reenter the command.

CONRELE E016

STORAGE REQUEST FOR COMMENT FAILED: RC = return_code

Reason:

The storage request failed because of insufficient storage.

Action:

Note the return code and contact your administrator.

CONRELE E017

NO COMMENT DATA SPECIFIED FOR RELATE COMMENT COMMAND.

Reason:

This message indicates that the comment data was not specified with the RELATE COMMENT command.

Action:

Add the data clause and reenter the command.

CONRELE E018

NO INPUT COMMANDS TO PROCESS.

Reason:

Use the CONRELE utility only if you have commands to process.

Action:

Do not use CONRELE if you do not have commands to process.

CONRELE I019

COMMANDS PROCESSED: command_count

Reason:

This message lists the number of commands processed.

Action:

None.

CONRELE I020

ELEMENT │ COMMANDS PROCESSED: command_count │ MEMBER │ │ OBJECT │ │COMMENT│

Reason:

This message lists the number of ELEMENT, MEMBER, OBJECT, or COMMENT commands processed.

Action:

None.

CONRELE I021

CONRELE PROCESSING SUCCESSFULLY COMPLETED.

Reason:

This message indicates that the CONRELE processing completed successfully.

Action:

None.

CONRELE E022

CONRELE PROCESSING COMPLETED WITH ERRORS, RC= return_code.

Reason:

The CONRELE processing completed with errors.

Action:

None.