SPLx is the CADDSPL ID
Reason:
This message is part of the initialization update of the ROOT LDS.
It indicates the end of the messages group.
Action:
None.
Reason:
The CADDUTIL utility is processing a ROOT command and the INIT or ALTER sub parameter has not been specified. Add the INIT sub parameter to the ROOT command when initializing a new ROOT LDS. Or add the ALTER sub parameter to the ROOT command when modifying a ROOT LDS.
Action:
Verify that the ROOT command specifies either the INIT or ALTER sub parameter.
Reason:
The SYSIN DD file was empty. The CADDUTIL utility ended without having processed any command.
Action:
Correct your SYSIN and rerun your batch job.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
An internal logic error occurred during the last command analysis.
Action:
Contact Technical Support.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
A syntax error occurred during the last command analysis due to a problem on the command line.
Action:
Check the syntax command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
An end of a command was detected at a place where the command needed an action.
Action:
Check the syntax command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
The value at offset nnnn is not a valid keyword for the given command.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
The value parameter at offset value was previously specified in the command.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
The parameter at offset nnnn specifies too many operands.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
An internal error occurred during the analysis of a specific parameter
Action:
Contact Technical Support.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
An internal error occurred during the analysis of a specific parameter
Action:
Contact Technical Support.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
A numeric value was found at offset nnnn.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
A dsname was found at offset nnnn.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
A ddname was found at offset nnnn.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
The ddname specified in the command at offset nnnn does not correspond to a DD statement.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
A member name was found at offset nnnn.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
The value specified at offset nnnn is too long to match the target field.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
The value specified at offset nnnn contains invalid characters.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
An internal error occurred during the analysis of a specific parameter
Action:
Contact Technical Support.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
An internal error occurred during the analysis of a specific parameter.
Action:
Contact Technical Support.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
An internal error occurred during the analysis of a specific parameter.
Action:
Contact Technical Support.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
The value specified at offset nnnn is either not numeric or it is out of range.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
The values specified are mutually exclusive.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
The Row value is prohibited for the Action parameter of the ADD command.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
The message task must have SAPI as an action value. Intercept and None are prohibited action values for the message task.
Action:
Check the command.
Reason:
This keyword was ignored in the specific ROOT command.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
'All' is an invalid task ID for the ADD and DEL commands.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
The required parameter or parameters are not present.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
keyword is not authorized for the function of the command.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
The required parameter, keyword, is missing for the command.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
The keyword or keywords for this command are missing.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
Two mutually exclusive functions were specified for the command.
Action:
Check the command.
Reason:
The ranges specified are consecutive and were merged together.
Action:
Check the command.
Reason:
The range low1:high1 is a part of the range low2:high2 and is ignored.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
One of the Util values is outside of its limit.
Action:
Check the command.
xxxx is a CADDUTIL ID (UTIL) or CADDSPL address space ID (SPLx)
Reason:
The All or None value cannot be specified with another value.
Action:
Check the command.
Reason:
An internal error occurred during the request for a new 4 KB block.
Action:
Contact Technical Support.
Reason:
An internal error occurred during the request for a new 4 KB block.
Action:
Contact Technical Support.
Reason:
An internal error occurred during the request for a new 4 KB block.
Action:
Contact Technical Support.
Reason:
An internal error occurred during the request for a new 4 KB block.
Action:
Contact Technical Support.
Reason:
An internal error occurred during the request for a new 4 KB block.
Action:
Contact Technical Support.
Reason:
An internal error occurred during the request for a new 4 KB block.
Action:
Contact Technical Support.
Reason:
An internal error occurred during the request for a new 4 KB block.
Action:
Contact Technical Support.
Reason:
An internal error occurred during the request for a new 4 KB block.
Action:
Contact Technical Support.
Reason:
An internal error occurred during the request for a new 4 KB block.
Action:
Contact Technical Support.
Reason:
The LDS is full and cannot free a data block.
For an intercepted report, the remaining part is rerouted on the JES spool and processed later by the SAPI task.
For a report processed by the SAPI task, the report waits until more space is available on the LDS or until a CLOSE command is sent.
Action:
Delete or archive any reports not immediately needed to release space in the LDS.
Reason:
An internal error occurred during the request for a new 4 KB block.
Action:
Contact Technical Support.
SPLx is the CADDSPL ID
text displays the current values of General and Access Registers at specific addresses in load module CADDSPLB.
Reason:
Informational message. These messages are issued in the CA Dispatch JOBLOG after command SET MSG=860 is entered. This command should be entered for debugging purpose only when requested by Technical Support.
Action:
Enter command RESET MSG=860 to prevent CADD860I messages from being issued.
SPLx identifies the CADDSPL environment.
Reason:
An INTERFACE parameter has been found for this environment and either no entry has been found in the CADDSNT or this entry is marked as not active.
Action:
Make sure all of the required CADDSPL environments are active and remove any INTERFACE parameter not required.
LDSROOTx identifies the DD card for a given LDS ROOT environment.
Reason:
32 LDS Root DD cards have already been selected which is a limit of CADDLIST. This LDSROOTx DD card will not be processed.
Action:
Make sure to not specify more than 32 LDSROOTx DD cards in the JCL.
LDSROOTx identifies the DD card for a given LDS ROOT environment.
Reason:
A DD card with the same DDname has already been selected. The current one is rejected.
Action:
Make sure to not specify more than one time the same LDSROOTx DD card in the JCL.
Reason:
Either the required LDSPRT DD card has not been found in the JCL or an error occurred during the OPEN process.
Action:
Make sure to specify the LDSPRT DD card in the JCL; this one must address either a SYSOUT file or an output file with a RECFM of VBA and a LRECL of 157.
Reason:
The required LDSPRT DD card has not been found in the JCL.
Action:
Make sure to specify the LDSPRT DD card in the JCL; this one must address a SYSOUT file.
Reason:
Informational message displaying the parameter card being analyzed.
Action:
None.
Reason:
The previously displayed parameter card contains an invalid parameter.
Action:
Make sure your card is SORT, SELECT, EXCLUDE or INTERFACE and suppress any other card.
Reason:
The previously displayed parameter card contains no value.
Action:
Correct your parameter card.
x is the current Interface id.
Reason:
More than 32 INTERFACE cards have been found in the LDSPARM.
Action:
Make sure to not specify more than 32 INTERFACE cards.
Note, INTERFACE * can be used for all active CADDSPL in the system.
x is the current Interface id.
Reason:
More than one INTERFACE card has been found in the LDSPARM for this ID.
Action:
Make sure to not specify more than one INTERFACE card for a given ID.
Note, INTERFACE * can be used for all active CADDSPLs in the system.
xxxxxxxx is the value found.
Reason:
The SORT parameter card contains an invalid value.
Action:
Make sure the value or the values on the SORT parameter card are JOBNAME, JOBID, TOKEN, REPORT or SIZE.
Reason:
There are too many values on the specified parameter card.
Action:
Make sure the number of values is accurate on the parameter card.
This number is 4 for the Sort parameter and 8 for the Select or Exclude parameter.
text indicate the kind of parameter card. It can be :
Reason:
Only one parameter card is allowed for each of the specified types.
Action:
Make sure to not specify more than one parameter card for each type.
Reason:
The SELECT or EXCLUDE parameter card contains an invalid keyword.
Action:
Make sure the value of the keyword is JOBNAME or REPORT.
xxxxxxxx is the value found.
Reason:
The SELECT or the EXCLUDE parameter card contains a value that is too long. The values specified either on the JOBNAME or on the REPORT keyword can not be longer than 8 characters.
Action:
Correct the invalid value.
Reason:
The INTERFACE * card, if specified, must be the only INTERFACE parameter card.
Action:
Correct the invalid value.
Reason:
The CADDSNT module cannot be located. That module contains the anchor point for the active CADDSPL environments. The utility has been started with one or multiple INTERFACE parameter cards while the CAIRIM program did not correctly initialize the CADDSPL anchor point.
Action:
Make sure the CADDSPL environments are started before the utility is started.
ddname is the ddname processing during OPEN or CLOSE function.
xxxx is the return code of the Storage function in hexadecimal value.
Reason:
The required storage cannot be obtained or released. The Storage return code gives more information about the reason.
Action:
Increase the REGION parameter on the JCL EXEC statement and rerun the job.
Reason:
An LDSROOTx DD card or an INTERFACE parameter card has not been found.
Action:
Specify either an LDSROOTx DD card or an INTERFACE parameter to indicate the environment to analyze.
Reason:
LDSROOTx DD card(s) and INTERFACE parameter card(s) have been found.
Action:
Specify either an LDSROOTx DD card(s) or INTERFACE parameter(s) to indicate the environment to analyze but not both.
LDSROOTx is the ddname of the Root LDS in the Open process.
xxxx is the return code of the Open function in hexadecimal value.
Reason:
An error occurred during the open process of a Root LDS file. The Open
return code gives more information about the reason.
Action:
Check the Open return code, correct the error, and rerun the job.
LDSROOTx is the ddname of the Root LDS in the Open process.
Reason:
The LDSROOTx DD card does not address a valid Root LDS.
Action:
Correct the DD card and rerun the job..
LDSROOTx is the ddname of the Root LDS in the read process.
Reason:
This is an internal error during the read process of the LDSROOTx file.
Action:
Contact Technical Support.
LDSROOTx is the ddname of the Root LDS in the read process.
xxxxxxxx is the feedback value of the VSAM GET function in hexadecimal format.
Reason:
Either a Logical or Physical error occurred during the read process of the LDSROOTx file.
Action:
See the IBM z/OS DFSMS Macro Instructions for Data Sets for an explanation of the Feedback code, correct the error and rerun the job.
Reason:
During a read process, the MVS system has determined the SMS component has not been started.
Action:
Check your last IPL process to determine the reason for this situation, correct it and rerun the job.
LDSxxxx is the ddname of the DD card in the Open process. It can be LDSPARM, LDSPRT, LDSLIST or LDSDUMP.
xxxx is the return code of the Open function in hexadecimal value.
Reason:
An error occurred during the open process of the referenced file. The Open return code gives more information about the reason.
Action:
Check the Open return code, correct the error and rerun the job.
SPLx is the id of CADDSPL environment.
LDSx is the id of the LDSROOTx DD.
xxxx is the return code of the sort function in hexadecimal value.
Reason:
Informational message.
Action:
Check the return code. If the return code is other than zero, see the appropriate Sort documentation.
LDSROOTx is the ddname of the Root LDS.
Reason:
This is an internal error. The program was not able to find the DSName of the Root LDS.
Action:
Check your DD card. If it refers to a valid Root LDS, contact Technical Support.
LDSROOTx is the ddname of the Root LDS
DSName is the dsname of the Root LDS
Reason:
Informational Message indicating the DSName of the Root LDS currently in process.
Action:
None.
|
Copyright © 2011 CA.
All rights reserved.
|
|