|
|
|
After powering up, the NBA will begin outputting text on the Console port. When the ROM password prompt appears, type N or let the prompt time out. You do not need a ROM password.
If the system has been powered up before and you have previously logged in as ‘admin’, go to step 2.
You must now manually enter the commands to set:
This is the internal network address for the system. You can use the default unless it matches a subnet already in use by the system elsewhere. If so, you will need to change the default. Go to step 4.
The management port network address that you provide should allow access to the CA DLP NBA software package. You will provide this address in step 5.
Example inputs are shown below:
System Name: system.ca.com CPU-X login: admin Password: Last login: Tue Jan 30 08:01:00 on /dev/tts/0 You are now logged in to CPU-X of system.ca.com BiviOS Version 3.2.5.9 (Build 200803051300) CLI Loading ................................ system[admin:]> configure interfaces system[admin:interfaces]> set interface mgt0 address 10.0.12.17 netmask 255.255.0.0 Conflict checking interface address...Done! system[admin:interfaces]> configure system Do you want to perform a "commit boot" on your changes? (y/n) [y] y Interface configuration committed. system[admin:system]> set mccp subnet address 10.10.10.0 * To change the MCCP subnet to 10.10.10.0, the system must be rebooted. Do you want to commit your changes and reboot now? (y/n) [y] y
=============================================================================== Please log in as user 'admin' to perform the initial setup routine =============================================================================== CPU-X login: admin
To finalize your installation, please answer the following questions. When you are done, the machine will be rebooted and then ready to use. The MCCP subnet needs to be a class C subnet that is only used internally. This cannot conflict with any traffic forwarded through this device, and also cannot conflict with any interfaces of this device. --------------------------------------------------------------------- MCCP subnet address ? [10.10.10.0] --------------------------------------------------------------------- Please verify your settings: MCCP subnet address : 10.10.10.0 --------------------------------------------------------------------- Is this correct? (y/n) [n] y
IP address for management port? [10.0.12.17] Network mask for management port? [255.255.0.0] Broadcast address for management port? [10.0.255.255] --------------------------------------------------------------------- Please verify your settings: IP address for management port: 10.0.12.17 Network mask for management port: 255.255.0.0 Broadcast address for management port: 10.0.255.255 --------------------------------------------------------------------- Is this correct? (y/n) [n] y
You may enter a default gateway now for your management port, or choose N and configure all routes later using 'configure staticroutes'. --------------------------------------------------------------------- Do you want to specify a default gateway now? (y/n) [n] n
Hostname (incl. domain name)? [] nba17.ca.com --------------------------------------------------------------------- Please verify your settings: Hostname (incl. domain name): nba17.ca.com --------------------------------------------------------------------- Is this correct? (y/n) [n] y
Do you want to specify a name server now? (y/n) [n] n
Next, please provide passwords for the standard system users:
root-> Privileged account for use by experts, in emergencies only
admin-> System administrator
You will see a warning about password strength; enter the same password again at the "Re-enter…" prompt to override the warning:
--------------------------------------------------------------------- Password for user: root New password: Bad password: too short Re-enter new password: Password for user: admin New password: Bad password: too simple Re-enter new password: Set the timezone at the next prompt. You can change this later if required.
When asked to confirm, type 'y'.
| Please select your timezone from the list below | --------------------------------------------------------------------- | 00 - Hawaii | 01 - Alaska | | 02 - Pacific Time | 03 - Arizona | | 04 - Mountain Time | 05 - Central Time | | 06 - Mexico City | 07 - Eastern Time | | 08 - Atlantic Time | 09 - Newfoundland | | 10 - Brazil/East | 11 - Buenos Aires | | 12 - UTC | 13 - Western Europe | | 14 - Central Europe | 15 - Eastern Europe | | 16 - Moscow | 17 - Calcutta | | 18 - China | 19 - Singapore | | 20 - Western Australia | 21 - Taipei | | 22 - Tokyo | 23 - Seoul | | 24 - Eastern Australia | | --------------------------------------------------------------------- | nn -> select | M -> wider selection (tzselect) | C -> Cancel| --------------------------------------------------------------------- Your selection > 12 Setting timezone to UTC Setting time/date to 05/27/2008 10:50. Is this correct? (y/n) [n] y --------------------------------------------------------------------- Tue May 27 10:50:00 UTC 2008
Wait until the ‘CPU-X login:’ prompt appears.
When you have completed these tasks, continue with the NBA software installation procedure.
| Copyright © 2011 CA. All rights reserved. | Email CA Technologies about this topic |