Control Options Summary

CAICCI Control Options › Control Options Summary - CAICCI

Control Options Summary - CAICCI

Control Option	Operands	Default Values
CCI	(RECYCLE)	n/a (not applicable)
CCI	(STATUS,[sysid])	n/a
CCI	(TERM)	n/a
CCICT	(component_name,#buffers,buffer_size,member_name)	n/a
CONNECT	(sysid,...)	n/a
DISPLAY,CONNECT	n/a	n/a
DISPLAY,LINK	n/a	n/a
DISPLAY,NODE	n/a	n/a
DISPLAY,PROTOCOL	n/a	n/a
DISPLAY,RECEIVER	n/a	n/a
DISPLAY,RESOURCE	n/a	n/a
DISPLAY,SYSID	n/a	n/a
GATEWAY	(protocol,netparm,retry,sysid, maxru,start/stop,netparm2)	retry=10, maxru=4096, start/stop=START/SHUT
GENERIC	(protocol,generic-name)	n/a
HOSTNAME	(hostname[,FORCE])	No hostname defaults to the VMCF subsystem nodename.
LOGGER	(string,buffer1,buffer2,Y\|N)	string=20, buffer1=12, buffer2=12, N
MAXRU	(nnnnn)	n/a
NODE	(protocol,netparm,retry,sysid, maxru,start/stop,netparm2)	retry=10, maxru=4096, start/stop=START/SHUT
NODEDATA	([DISPLAY\|RESET,]protocol, sysid,netparm)	n/a
PERMIT	(NONE\|ALL)	ALL
PROTOCOL	(protocol,netparm,retry,sysid,maxru,start/stop)	retry=10, maxru=4096, start/stop=START/SHUT
PROTSEC	(XCF\|XES\|XES,XCF\|XCF,XES)	n/a
REMOVE	(SYSID,xxxxxxxx)	n/a
SYSID	(sysid)	n/a
SYSPLEX	(sysplexid)	n/a
VARY	(INACT\|ACT,SYSID,sysid)	n/a

Notes:

In the control option descriptions that are found in this guide, MAXRU is used as a control option and an operand for the GATEWAY, PROTOCOL, and NODE control options. MAXRU is the maximum data packet size, which is specified in bytes, that is allowed to be transmitted between two CAICCI subsystems. You can redefine the maximum RU default value of 4096 using this control option.
To determine the required MAXRU for hosts that are communicating using VTAM and are connected using NCP, see the MAXDATA operand of the PCCU macro, the BUFSIZE of the BUILD macro, and the INBFRS, MAXBFRU, and UNITSZ operands of the HOST macro.

To determine the required MAXRU for hosts that are connected using CTC, see your VTAM start option LPBUF.

See the IBM reference guides and consult with your VTAM/NCP Systems Programmer for more information.
Use the CCI(RECYCLE) and CCI(TERM) control options only under the direction of CA Support.
The CONNECT control option refers to definitions made using the GATEWAY and NODE control options to perform actual CAICCI linking.
The GATEWAY and NODE control options establish CAICCI control blocks.
The keyword SHUT is equivalent to the keyword STOP. Either can be coded to indicate that session termination occurs at the CAICCI shutdown.
With IPv6 addresses, use coded delimiters to identify the start and end of the address separate from the port number.
Any of the following character pairs can be used as delimiters:
```
start "["   end "]"
start "<"   end ">"
start and end "/"
start and end "\"
start and end "|"
```
In the following example, coded brackets "[" and "]" delimit the start and end of the IPv6 address.
```
[fd00:7a06:a20:100::11]:7001
```