Configuration Steps

Configuring Your Product › How to Configure CA Common Services Without CA CSM › Configuration Steps

Configuration Steps

Note: For information concerning APF authorizing data sets, and adding data sets to the link list and LPA, see the IBM z/OS MVS Initialization and Tuning Reference.

To configure your system before starting CA Common Services for z/OS

APF Authorize Data Sets
1. Determine if your site is using SYS1.PARMLIB member IEAAPFxx or PROGxx to specify the APF list.
2. Add the following data sets that apply to the SYS1.PARMLIB APF list member your site is using:
  - YourdeployHLQ.CAW0LOAD – BASE component Installation
  - YourdeployHLQ.CCCSLOAD – LEGACY component Installation
  - YourdeployHLQ.CNSMLOAD – MFNSM component Installation
  - YourdeployHLQ.CNSMPLD – MFNSM component Installation
  - YourdeployHLQ.CAW0DCM – BASE component Installation - CAIENF
  - YourdeployHLQ.CAW0LINK – BASE component Installation
  - YourdeployHLQ.CCCSLINK – LEGACY component Installation
  - YourdeployHLQ.CAW0PLD – BASE component Installation
  - YourdeployHLQ.CC2DLINK – HIS and Linux Connector Installation
  - YourdeployHLQ.CC2DLOAD – HIS and Linux Connector Installation
  Important! Failure to APF-authorize these data sets can result in the incorrect completion of jobs in the configuration process or the failure to start address spaces.
Link List Data Sets
1. Determine if your site is using SYS1.PARMLIB member LNKLSTxx or PROGxx to specify the LNKLST concatenation.
2. Add the following data sets that apply to the SYS1.PARMLIB link list member your site is using:
  - YourdeployHLQ.CAW0LINK – BASE component Installation
  - YourdeployHLQ.CAW0PLD – BASE component Installation
  - YourdeployHLQ.CCCSLINK – LEGACY component Installation
  - YourdeployHLQ.CNSMLOAD – MFNSM component installation
  - YourdeployHLQ.CC2DLINK – HIS and Linux Connector Installation
3. (Optional) Add the following data sets that apply to the SYS1.PARMLIB link list member your site is using, to use the system link list rather than using STEPLIB in the CA product and Common Services related JCL:
  - YourdeployHLQ.CAW0LOAD – BASE component Installation
  - YourdeployHLQ.CCCSLOAD – LEGACY component Installation
  - YourdeployHLQ.CC2DLOAD – HIS and Linux Connector Installation
  Important: Because this load library contains common CA Management Services modules, if any of the following software is installed at your site do not linklist this library: Chorus, CMDB Connector, NetMaster, OPS/MVS WebCenter, or SOLVE. Doing so can impact backward and forward compatibility with these software products.
Add the following data sets that apply to the SYS1.PARMLIB LPA list member, LPALSTxx your site is using:
- YourdeployHLQ.CAW0LPA – BASE Installation if the system is running a z/OS release below 1.13.
- YourdeployHLQ.CC2DLPA – Linux Connector Installation

Update the program properties table.

Your installation must define a program properties table entry for each of the CA Common Services that apply to your site. These entries reside in the SCHEDxx member of the logical PARMLIB concatenation. You can apply this update dynamically with an operator SET SCH=(xx,yy,zz,L) command.

Place the following program properties table (PPT) statements that apply in your SCHEDxx PARMLIB member:

CA Common Service Address Space shell PPT entry:

PPT PGMNAME(CASRVASI)        /* CA-SERV Address Space Control Program   */
    KEY(4)                   /* EXECUTION KEY                           */
    NOSWAP                   /* NON-SWAPPABLE                           */
    PRIV                     /* PRIVILEGED                              */
    SYST                     /* SYSTEM TASK                         */
    LPREF                    /* Long-term PGFIX in non-reconfig stg */
    NOPREF                   /* Short-term PGFIX in reconfig stg    */

CA Common Variable Service PPT entry:
Note: For this service, the CA Common Service Address Space shell PPT entry from the first bullet is also required.
```
PPT PGMNAME(CAVDMAIN)           /* CAVARSRV ADDRESS SPACE MAIN PGM */
    KEY(4)                      /* EXECUTION KEY  */
```

Perform Component Configuration Steps:
- CAIRIM Configuration Tasks
- CAIENF Configuration Tasks
- CAICCI Configuration Tasks
- Event Management Configuration Tasks
- Agent Technology Configuration Tasks
- CA Global SubSystem Configuration Tasks
- CA-L-Serv Configuration Tasks
- Other Configuration Tasks
Save All Materials and Outputs.
This step is important to make information available for maintenance and upgrade purposes.