Previous Topic: CSP ConsoleNext Topic: Configure the CSP Console Properties File

Installation Guide › Server Installation › CSP Console › CSP Console Pre-Installation Steps

CSP Console Pre-Installation Steps

To prepare for installation, confirm that your server environment is properly prepared. Then install the required packages.

Important! The host name of the machine where you install the CSP Console must contain lower case letters only. If the host name includes upper case letters, the CSP Console does not open, and a looping error occurs in the log.

Follow these steps:

  1. Install 64-bit Linux RHEL 6.1.
  2. Download, but do not install, a 32-bit JDK and a 64-bit JDK to your local system or to a file share.

    Note: The system installer can install the JDK automatically. We recommend that you download a JDK and allow the system to install it.

    Important! The CSP console installation requires a JDK, rather than a JRE.

  3. Download, but do not install, JBoss 5.1.0 to your local system or to a file share.

    Note: The system installer JBoss automatically.

  4. Verify Oracle is configured as follows:
  5. Obtain the SiteMinder Policy Server ISO image from the CA Support site and extract it.
  6. Copy the kit (CAM-SMPS_kit-date.zip) to / (the root folder).
  7. Unzip the kit.
  8. Install the following packages required for Advanced Authentication
  9. Install the Korn shell packages at /bin/ksh.
  10. Run the following commands to set the state of the firewall/ip tables: 
    chkconfig iptables off
service iptables stop
  11. Run the following commands to check and set the state of SELinux:
    1. Check the status: 
      sestatus
    2. If the response is "permissive" or "disabled", do nothing
    3. If the response is "enforcing", change the state: 
      sudo vi /etc/selinux/config
setenforce 0
  12. Enter the following commands: 
    echo "[0001]" >> /etc/yum.conf
echo "mediaid=`head -n 1 /media/RHEL_6.1\ x86_64\ Disc\ 1/.discinfo`"  >> /etc/yum.conf
echo "name=respooracle" >> /etc/yum.conf
echo "baseurl=file:///media/RHEL_6.1\ x86_64\ Disc\ 1/" >> /etc/yum.conf
echo "enabled=1" >> /etc/yum.conf	
echo "gpgcheck=0" >> /etc/yum.conf
 
yum  install -y binutils-2*x86_64*
yum  install -y glibc-2*x86_64* nss-softokn-freebl-3*x86_64*
yum  install -y glibc-2*i686* nss-softokn-freebl-3*i686*
yum  install -y compat-libstdc++-33*x86_64*
yum  install -y glibc-common-2*x86_64*
yum  install -y glibc-devel-2*x86_64*
yum  install -y glibc-devel-2*i686*
yum  install -y glibc-headers-2*x86_64*
yum  install -y elfutils-libelf-0*x86_64*

yum  install -y elfutils-libelf-devel-0*x86_64*
yum  install -y gcc-4*x86_64*
yum  install -y gcc-c++-4*x86_64*
yum  install -y ksh-*x86_64*
yum  install -y libaio-0*x86_64*
yum  install -y libaio-devel-0*x86_64*
yum  install -y libaio-0*i686*
yum  install -y libaio-devel-0*i686*
yum  install -y libgcc-4*x86_64*

yum  install -y libgcc-4*i686*
yum  install -y libstdc++-4*x86_64*
yum  install -y libstdc++-4*i686*
yum  install -y libstdc++-devel-4*x86_64*
yum  install -y make-3.81*x86_64*
yum  install -y numactl-devel-2*x86_64*
yum  install -y sysstat-9*x86_64*
yum  install -y compat-libstdc++-33*i686*
yum  install -y compat-libcap*
yum  install -y unixODBC*

yum  install -y libstdc++*
yum  install -y compat-libstdc++-33.i686
yum  install -y compat-libstdc++-296.i686
yum  install -y glibc.i686
yum  install -y ksh.x86_64
yum  install -y libgcc.i686
yum  install -y libidn.i686
yum  install -y libstdc++.i686

yum  install -y libX11.x86_64
yum  install -y libXau.x86_64
yum  install -y libxcb.x86_64
yum  install -y libXext.i686
yum  install -y libXi.i686
yum  install -y libXtst.i686
yum  install -y ncurses-devel.i686
yum  install -y nss-softokn-freebl.i686
yum  install -y dos2unix
yum  install -y telnet
rpm -i compat-libtermcap-2.0.8-49.el6.i686.rpm
  13. Make sure that the following soft link still exists. Reverting a virtual machine snapshot removes this link. 
    mv /dev/random /dev/random.orig
ln -s /dev/urandom /dev/random