Utility Report Messages › TMSINIT Messages

TMSINIT Messages

** MEMBER NOT FOUND **

Reason:

This message is issued by TMSINITD. The TMOSCRxx or TMONSMxx member was not found.

Action:

Add the missing member to CAI.CTAPOPTN and rerun TMSINIT.

** OPTIONS IN ERROR **

Reason:

Errors have been found while processing a CAI.CTAPOPTN member.

Action:

See the error message listed for additional information.

** TMSPARM NOT OPENED **

Reason:

The data set specified by the TMSPARM ddname could not be opened.

Action:

Correct the JCL and rerun TMSINIT.

** xxxxxxx NOT FOUND **

Reason:

The TMSKEYAB, TMSPLIO or TMOOPTxx member was not found.

Action:

If the missing member is TMOOPTxx, add the missing member toCAI. CTAPOPTN and rerun TMSINIT. Otherwise, contact your systems programmer responsible for maintaining CA 1.

** xxxxxxxx EMPTY **

Reason:

The member listed did not contain any records.

Action:

Add the missing information to the member in CAI.CTAPOPTN and rerun TMSINIT.

AT LEAST 1 KEYWORD MUST BE SPECIFIED

Reason:

This message is issued by TMSINITE. At least one of the following keywords must be specified in the TMOEDMxx member: DSN=, JOB=, PGM= or DD=.

Action:

Correct the control statement and rerun TMSINIT.

BAD MASKING COMBINATION SPECIFIED

Reason:

This message is issued by TMSINITE. An invalid masking specification was encountered in the TMOEDMxx member.

Action:

Correct the control statement and rerun TMSINIT.

BEGINNING xxxxxxxx ÄAND xxxxxxxx¬ PROCEDURE

Reason:

Validation processing for the CAI.CTAPOPTN member xxxxxxxx has begun.

Action:

None. This is an informational message.

CTSINITP PROCESSING FOR CTAPOPTN MEMBER xxxxxxxx COMPLETE

Reason:

The informational messages generated during initialization processing are reported on TMS Report 00 - Initialization Report to identify the specific processing which occurred.

Action:

None. This is an informational message.

CTSINITP PROCESSING FOR CTAPOPTN MEMBER xxxxxxxx FAILED,RC=xx

Reason:

A CAI.CTAPOPTN member could not be processed by TMSINITD. The CAI.CTAPOPTN member shown in the message is either TMOSCRxx or TMONSMxx.

The return codes are:

04 Syntax error in CAI.CTAPOPTN member

08 Program logic error

0C Insufficient storage for execution

10 CAI.CTAPOPTN member not found

14 I/O error on CAI.CTAPOPTN

18 TMOSCRxx and TMONSMxx members out of sync or bad TMSXITE or TMSXITU exit routine

Action:

Correct the error and rerun TMSINIT.

DSN, JOB, UNIT INVALID WITH MGMTCLAS KEYWORD

Reason:

This message is issued by TMSINITD. Another keyword has been specified with the MGMTCLAS keyword in the TMONSMxx member. This is not allowed.

Action:

Correct the control statement and rerun TMSINIT.

DSN, JOB, UNIT, OR MGMTCLAS KEYWORD NOT FOUND

Reason:

This message is issued by TMSINITD.A required keyword was not found in the control statement in the TMONSMxx member.

Action:

Correct the control statement and rerun TMSINIT.

DSN KEYWORD APPEARS MORE THAN ONCE

Reason:

This message is issued by TMSINITD. The DSN keyword was specified more than once in the control statement in the TMONSMxx member.

Action:

Correct the control statement and rerun TMSINIT.

DSN OR JOB KEYWORD NOT FOUND

Reason:

This message is issued by TMSINITD. The DSN keyword or the JOB keyword was not found in a control statement in the TMONSMxx member.

Action:

Correct the control statement and rerun TMSINIT.

DUPLICATE KEYWORD OR MISSING EDM KEYWORD

Reason:

This message is issued by TMSINITE. A duplicate or missing keyword was found in the TMOEDMxx member.

Action:

Correct the keyword in the TMOEDMxx member and rerun TMSINIT.

DUPLICATE PARAMETER - xxxxxxxx

Reason:

A duplicate parameter was specified in TMSINIT.

Action:

Review the Initialization Report for specific information on the error. Correct the JCL and rerun TMSINIT.

EDM=xxxx specified in NSM member not found in EDM table

Reason:

In the NSM member a reference was made to EDMxxxx. However, that EDM was not defined in the EDM member.

Action:

Either add the specified EDM to the EDM member, or reference a valid EDM in the NSM member.

ERROR TRAPPED BY SYNAD EXIT: xxxxxxxx

Reason:

An I/O error occurred during initialization processing.

Action:

The message identifies the type of error. Correct the error and rerun TMSINIT.

EXECUTION PARAMETERS RECEIVED EXCEED MAXIMUM LENGTH

Reason:

The total length of execution parameters provided to TMSINIT is not less than 80.

Action:

Correct the JCL and rerun TMSINIT.

EXECUTION PARAMETERS RECEIVED=xxx

Reason:

The parameter information identified by xxx was provided through the PARM keyword when TMSINIT was started.

Action:

None. This is an informational message.

FIRST NON-BLANK FIELD IS NOT A KEYWORD

Reason:

This message is issued by TMSINITE. An invalid keyword was found in the TMOEDMxx member.

Action:

Correct the keyword in the TMOEDMxx member and rerun TMSINIT.

IEFTMS1 CA 1 (TMS) IS ACTIVE

Reason:

CA 1 has been initialized and is active and ready for use.

Action:

None. This is an informational message.

Note: If you receive this message without having previously received the IEFTMS0 message(s), there may be a problem with your system. For assistance, contact Technical Support at http://ca.com/support.

IEFTMS1 CA 1 (TMS) IS BATCH ACTIVE

Reason:

CA 1 has been made active in batch mode. Tape processing is not tracked.

Action:

None. CA 1 has been made active for batch processing and online inquiry only. The TMC is not updated for tapes going through OPEN, CLOSE and EOV in this mode. To reactivate, execute TMSINIT, and reply U at the IEFTMS0 prompt.

IEFTMS1 CA 1 (TMS) IS INACTIVE

Reason:

CA 1 has been deactivated. Tape processing is not tracked.

Action:

None. Once CA 1 has been deactivated, it can be reactivated only by running TMSINIT.

IEFTMS1 CA 1(TMS) HAS TESTED CA 1 PPOPTION MEMBERS

Reason:

A parameter of TEST was used. Only testing of applicable CAI.CTAPOPTN members (that would have been used if a parameter of TEST had not been specified) has occurred. No modification of CA 1 status has occurred.

Action:

None. This is an informational message.

IEFTMS1 TEMPAUDT DD STATEMENT MISSING

Reason:

TMSINIT did not find or was unable to open the data set pointed to by the TEMPAUDT ddname. TEMPAUDT is required for TMSINIT processing.

Action:

Correct the JCL and rerun TMSINIT.

IEFTMS1 TMSRPT DD MISSING

Reason:

This message is issued by TMSINITD, which is called by TMSINIT. The TMSRPT DD statement is missing.

Action:

Correct the JCL and rerun TMSINIT.

IEFTMS12 - ERROR BUILDING OPTIONS TABLE, KEYWORD keyword NOTDEFINED, IGNORED

Reason:

This message is issued by TMSOPTB. CAI.CTAPOPTN member TMOOPTxx contains an invalid option override statement. CA 1 initialization continues.

Action:

See the CA 1 Initialization Report produced by TMSINIT to determine which statement is in error. Edit the TMOOPTxx member to correct the statement and rerun TMSINIT.

IEFTMS12 - ERROR BUILDING OPTIONS TABLE, OPTION option SET TO data

Reason:

This message is issued by TMSOPTB. An option override statement specified an invalid option value. CA 1 initialization continues.

Action:

See the CA 1 Initialization Report produced by TMSINIT to determine which statement is in error, edit the TMOOPTxx member to correct the statement, and rerun TMSINIT.

IEFTMS12 - ERROR BUILDING OPTIONS TABLE, OPTION xxxxxxxx IS INVALID

Reason:

This message is issued by TMSOPTB. The value specified for a keyword in the TMOOPTxx member is not valid.

Action:

Correct the keyword specification in the TMOOPTxx member and rerun TMSINIT.

ERROR BUILDING OPTIONS TABLE, OPTION option IS A DUPLICATE

Reason:

The option displayed in message IEFTMS12 was found duplicated in the TMOOPTxx member of CTAPOPTN. The last option found will actually be the one used. CA 1 initialization continues.

Action:

It is recommended that duplicate options be removed from the TMOOPTxx member. This will prevent problems when it is thought that a specific option is specified one way, when a duplicate entry actually causes the option to work in a different way.

INVALID KEYWORD

Reason:

This message is issued by TMSINITD. An invalid keyword specified in a control statement in either the TMOSCRxx or TMONSMxx member was not found in the keyword table, TMSKEYAB.

Action:

Correct the control statement and rerun TMSINIT.

INVALID KEYWORD VALUE LENGTH

Reason:

This message is issued by TMSINITD. A control statement specified in either the TMOSCRxx or TMONSMxx member contains a keyword value length that is either too large or too small.

Action:

Correct the control statement and rerun TMSINIT.

INVALID PARAMETER COMBINATION

Reason:

The parameters passed to TMSINIT include an invalid combination.

Action:

Correct the JCL and rerun TMSINIT.

INVALID PARAMETER - xxxxxxxx

Reason:

An invalid parameter was detected during TMSINIT processing. Until TMSINIT has been successfully executed, no tape jobs of any kind can be executed.

Action:

Review the report produced by TMSINIT for any parameter errors. If the report is not available, execute TMSINIT as a batch job. Correct the JCL and rerun TMSINIT.

INVALID PARM - xxxxxxxx

Reason:

This message is issued by TMSINITD. An invalid scratch pool parameter was passed by TMSINIT or in batch mode.

Action:

Verify the SCR=xx or NSM=xx members provided. Rerun TMSINIT with the correct TMOSCRxx and TMONSMxx members.

INVALID RANGE SPECIFICATION

Reason:

This message is issued by TMSINITD. The range specification is not consecutive for the keyword RANGE, or the dash separating the range specification is missing in the TMOSCRxx member.

Action:

Correct the control statement and rerun TMSINIT.

INVALID RANGE VOLSER(S)

Reason:

This message is issued by TMSINITD. The volume serial number range specifications for the keyword RANGE in the TMOSCRxx member contains a volume serial number that is not defined to the current TMC (according to TMSXITU), or is greater than six characters.

Action:

Correct the control statement and rerun TMSINIT.

INVALID STATEMENT SYNTAX

Reason:

This message is issued by TMSINITD. A syntax error was detected in a control statement in either the TMOSCRxx or TMONSMxx member.

Action:

Correct the control statement and rerun TMSINIT.

MAXFILES and THRESHOLD keywords must be all numeric values

Reason:

MAXFILES and THRESHOLD keywords are not numeric values.

Action:

Supply numeric values in CTAPOPTN member TMOSCRxx.

MAXFILES keyword appears more than once

Reason:

There are duplicate MAXFILES keywords.

Action:

Remove duplicate keywords in CTAPOPTN member TMOSCRxx.

JOB KEYWORD APPEARS MORE THAN ONCE

Reason:

This message is issued by TMSINITD. The JOB keyword was specified more than once in the control statement in the TMONSMxx member.

Action:

Correct the control statement and rerun TMSINIT.

MGMTCLAS KEYWORD APPEARS MORE THAN ONCE

Reason:

This message is issued by TMSINITD. The MGMTCLAS keyword was specified more than once in the control statement in the TMONSMxx member.

Action:

Correct the control statement and rerun TMSINIT.

MISSING EDM KEYWORD

Reason:

This message is issued by TMSINITE. The EDM keyword was not found in the TMOEDMxx member.

Action:

Correct the control statement and rerun TMSINIT.

NCAT keyword appears more than once

Reason:

There are duplicate NCAT keywords.

Action:

Remove duplicate keywords in CTAPOPTN member TMOSCRxx.

NCAT keyword must be "STACK" or "NEXT"

Reason:

Incorrect keyword used for NCAT.

Action:

Supply correct keyword in CTAPOPTN member TMOSCRxx.

MISSING OR INVALID OVERRIDE VALUE FOR xxx

Reason:

A parameter value specification is invalid.

Action:

Correct the JCL and rerun TMSINIT.

NO EXECUTION PARAMETERS RECEIVED

Reason:

No parameter information was provided through the PARM keyword when TMSINIT was started.

Action:

None. This is an informational message.

NSM RULE nanny IS A DUPLICATE OF RULE mmmmm

Reason:

This message is issued by TMSINITD. The indicated control statement number in the TMONSMxx member duplicates another control statement in that member.

Action:

Correct the control statement and rerun TMSINIT.

NUMBER OF SCRATCH POOL RANGES EXCEEDS 255 MAX

Reason:

This message is issued by TMSINITD. The number of RANGE keywords has exceeded the maximum of 255.

Action:

Correct the control statement and rerun TMSINIT.

OPEN ERROR ON CTAPOPTN MEMBER: xxxxxxxx, RC=xx
READ ERROR ON CTAPOPTN MEMBER: xxxxxxxx, RC=xx

Reason:

There was an OPEN or READ error in CAI.CTAPOPTN. The CAI.CTAPOPTN member appears in the message with the return code, which identifies the type of error.

The return codes are:

00 Successful completion

04 CAI.CTAPOPTN member empty (options set to default)

08 CAI.CTAPOPTN member not found

0C TMSPARM DD could not be opened

10 CAI.CTAPOPTN access routine could not be loaded

18 TMS Keyword Table (TMSKEYAB) in error

1C Table created, some options in error

20 I/O error occurred reading CAI.CTAPOPTN

Action:

Correct the error and resubmit TMSINIT.

PARAMETER TOO LARGE OR SMALL FOR KEYWORD

Reason:

This message is issued by TMSINITE. The parameter specified in the TMOEDMxx member is invalid.

Action:

Correct the keyword in the TMOEDMxx member and rerun TMSINIT.

POOL KEYWORD APPEARS MORE THAN ONCE

Reason:

This message is issued by TMSINITD. The POOL keyword was specified more than once in the control statement of the TMONSMxx member.

Action:

Correct the control statement and rerun TMSINIT.

POOL KEYWORD NOT FOUND

Reason:

This message is issued by TMSINITD. The POOL keyword was not found in a control statement in the TMONSMxx member.

Action:

Correct the control statement and rerun TMSINIT.

POOLNAME NOT FOUND IN SCRATCH SUBPOOL TABLE

Reason:

This message is issued by TMSINITD. A SCRPOOL name on the TMONSMxx control statement was not defined in any TMOSCRxx member read.

Action:

Correct the control statement and rerun TMSINIT.

RANGE keyword(s) must be used after STACK or stacking keywords

Reason:

Incorrect keywords have been used.

Action:

Supply correct RANGE keywords in CTAPOPTN member TMOSCRxx.

RANGE KEYWORD NOT FOUND

Reason:

This message is issued by TMSINITD. The keyword RANGE must be specified in the control statement of the TMOSCRxx member.

Action:

Correct the control statement and rerun TMSINIT.

RANGE OVERLAPS WITH RANGE PREVIOUSLY DEFINED

Reason:

This message is issued by TMSINITD. A range specification in the TMOSCRxx member includes a volume serial number defined by another control statement.

Action:

Correct the control statement and rerun TMSINIT.

SCRATCH SUBPOOL NAME PREVIOUSLY DEFINED

Reason:

This message is issued by TMSINITD. A scratch subpool name specified in a control statement in the TMOSCRxx member was previously defined in another control statement.

Action:

Correct the control statement and rerun TMSINIT.

SCRPOOL KEYWORD APPEARS MORE THAN ONCE

Reason:

This message is issued by TMSINITD. The keyword SCRPOOL appears more than once in a control statement in the TMOSCRxx member.

Action:

Correct the control statement and rerun TMSINIT.

SCRPOOL NOT FIRST KEYWORD

Reason:

This message is issued by TMSINITD. The keyword SCRPOOL must be the first keyword in the control statement in the TMOSCRxx member.

Action:

Correct the control statement and rerun TMSINIT.

STACK keyword appears more than once

Reason:

There are duplicate STACK keywords.

Action:

Remove duplicate keywords in CTAPOPTN member TMOSCRxx.

STACK keyword must be "YES" or "NO"

Reason:

STACK keyword is incorrect.

Action:

Supply correct keyword in CTAPOPTN member TMOSCRxx.

SNEXT keyword appears more than once

Reason:

There are duplicate SNEXT keywords.

Action:

Remove duplicate keywords in CTAPOPTN member TMOSCRxx.

SNEXT keyword must be "SCRATCH" or "SPECIFIC"

Reason:

Incorrect keyword used for SNEXT.

Action:

Supply correct keyword in CTAPOPTN member TMOSCRxx.

THRESHOLD keyword appears more than once

Reason:

There are duplicate THRESHOLD keywords.

Action:

Remove duplicate keywords in CTAPOPTN member TMOSCRxx.

THRESHOLD keyword cannot be greater than a value of 100

Reason:

THRESHOLD keyword is greater than 100.

Action:

Change THRESHOLD keyword to be 100 or less in CTAPOPTN member TMOSCRxx.

** TMSKEYXB NOT CURRENTLY ANCHORED **

Reason:

TMSKEYXB was not successfully loaded into TMVT before TMSINIT execution.

Action:

Verify that CAS9 was run with the correct control statement and that TMSKEYXB was loaded. Correct any problems.

UNIT KEYWORD APPEARS MORE THAN ONCE

Reason:

This message is issued by TMSINITD. The UNIT keyword was specified more than once in the control statement of the TMONSMxx member.

Action:

Correct the control statement and rerun TMSINIT.

UNIT KEYWORD CONTAINS INVALID CHARACTER

Reason:

This message is issued by TMSINITD. The value specified for the UNIT keyword can consist only of 0 through 9, A through F, and pattern masking characters in the TMONSMxx member.

Action:

Correct the control statement and rerun TMSINIT.

xxxxxxxx PROCESSING COMPLETE

Reason:

Processing for CAI.CTAPOPTN member xxxxxxxx is complete.

Action:

None. This is an informational message.