Utility Report Messages › TMSEARL Messages

TMSEARL Messages

TMSEARL01 - UNSUCCESSFUL OPEN FOR xxxxxxxxxx

Reason:

The specified field could not be properly opened for processing. The file represented by xxxxxxxxxx was determined from the setting of the variable TYPRUN.

Action:

Examine accompanying messages for more detailed information, correct, and resubmit the job.

TMSEARL02 - INVALID TYPRUN GIVEN - xxxxxxxx

Reason:

The value for TYPRUN is not VOLUME, SEQUENTIAL, CHAINED,REPORT, VAULT, AUDIT or RETENTION.

Action:

Correct the control statement and resubmit the job.

TMSEARL03 - INITIALIZING FOR xxxxxxxxxx PROCESSING

Reason:

The variable TYPRUN was set to xxxxxxxxxx to indicate the type of processing desired.

Action:

None. This is an informational message.

TMSEARL06 - *** CA 1 IS NOT ACTIVE ***

Reason:

CHAINED processing was requested but CA 1 is not active. CA 1must be at least batch active for CHAINED processing.

Action:

Initialize CA 1 and then resubmit the job.

TMSEARL07 - VOLSER=vvvvvv NOT FOUND

Reason:

A direct read for volume vvvvvv was attempted; however, the volume is not on the TMC. This message is followed by message TMSEARL08.

Action:

Modify the CA-Earl program to refer only to volumes that are on the TMC and resubmit the job.

TMSEARL08 - *** TMSEARL ABORTING ***

Reason:

A critical error has occurred which prevents TMSEARL from continuing processing.

Action:

Examine accompanying messages for more detailed information, correct, and resubmit the job.

TMSEARL09 - VOLUME DIRECT READ FAILURE

Reason:

A direct read of a volume record encountered an error. This message is followed by message TMSEARL08.

Action:

Examine accompanying messages for more detailed information, correct, and resubmit the job.

TMSEARL10 - DSNB DIRECT READ FAILURE

Reason:

A direct read of a DSNB record encountered an error. This message is followed by message TMSEARL08.

Action:

Examine accompanying messages for more detailed information, correct, and resubmit the job.

TMSEARL11 - *** INVALID VOLUME CHAIN ***

Reason:

A volume chaining error on the TMC has been detected. This message is followed by messages TMSEARL12 and TMSEARL08.

Action:

Examine accompanying messages for more detailed information, correct, and resubmit the job.

TMSEARL12 - VOLUME/VOLSEQ --->vvvvvv-sss NOT ONE GREATER THAN PREVIOUS --->vvvvvv-sss

Reason:

A volume chaining error on the TMC has been detected. The volume serial numbers and volume sequence numbers are shown for analysis.

Action:

The TMC chaining pointers must be corrected. Run CA 1 utility TMSBINQ to do an inquiry of the volume(s) shown. You should also run CA 1 utility TMSPTRS to report on chaining errors. Correct and resubmit the job.

TMSEARL13 - UNSUCCESSFUL OPEN FOR RETENTION FILE

Reason:

TYPRUN was set to RETENTION but the retention file could not be properly opened for sequential input processing.

Action:

Examine accompanying messages for more detailed information, correct, and resubmit the job.

TMSEARL14 - *** INVALID DSNB CHAIN ***

Reason:

A volume chaining error on the TMC has been detected. This message is followed by messages TMSEARL15 and TMSEARL08.

Action:

Examine accompanying messages for more detailed information, correct, and resubmit the job.

TMSEARL15 - VOLUME/FILSEQ --->vvvvvv-sss NOT ONE GREATERTHAN PREVIOUS --->vvvvvv-sss

Reason:

A DSNB chaining error on the TMC has been detected. The volume serial numbers and file sequence numbers are shown for analysis.

Action:

The TMC chaining pointers must be corrected. Run the CA 1 utility TMSBINQ to do an inquiry of the volume(s) shown. You should also run TMSPTRS to report on chaining errors. Correct and resubmit the job.

TMSEARL16 - INVALID CA 1 AUDIT FILE

Reason:

The CA 1 Audit file does not contain Control Record #4(TMSCTL#4) as the first record of the data set.

Action:

Ensure that the TAPEDB DD statement points to a valid CA 1 Audit data set. Correct, and resubmit the job.