Reason:
The threshold value of the Audit data set has been exceeded.
Action:
Execute TMSCOPY to back up the TMC and Audit data set, and resubmit the job.
Reason:
The IDCAMS DD was provided but no tape data sets with a file sequence of 1 were found within the IDCAMS data set.
Action:
If the system running TMSCTLG has access to all catalogs to which tape data sets are cataloged, no action is required. However, if the system does not have access to all catalogs, review the expired catalog listing for expiration of cataloged tape data sets. See the JCL example for correct syntax and use TMSUPDTE, TMSUDSNB or CA 1 online facilities to update the EXPDT in these records to CATALOG. This must be done prior to running TMSCLEAN to prevent premature scratching of volumes.
Reason:
The IEHLIST DD was provided but no tape data sets with a file sequence of 1 were found within the IEHLIST data set.
Action:
If the system running TMSCTLG has LOCATE access to all catalogs to which tape data sets are cataloged, no action is required. However, if the system does not have access to all catalogs, review the expired catalog listing for expiration of cataloged tape data sets. See the JCL example for correct syntax, and use TMSUPDTE, TMSUDSNB or CA 1 online facilities to update the EXPDT in these records to CATALOG. This must be done prior to running TMSCLEAN to prevent premature scratching of volumes.
Reason:
No Volume records with an EXPDT=CATALOG and VOLSEQ=1 were found on the TMC.
Action:
None. This is an informational message.
Reason:
The CDATE (creation date) for this volume is 0.
Action:
The volume is not expired by TMSCTLG. Update the CDATE for this volume.
Reason:
A multivolume chain under Catalog Control contains a Volume record which has one of the following errors:
(*** Error: no level 15 lists allowed. ***)The NEXTVOL of vvvvvv is not defined in the volume ranges of TMC Control records #1 and #3.
(*** Error: no level 15 lists allowed. ***)The PREVVOL of this volume is not equal to the volser of volume vvvvvv.
(*** Error: no level 15 lists allowed. ***)The current volume's VOLSEQ is not equal to VOLSEQ + 1 of volume vvvvvv.
Action:
Execute TMSPTRS to analyze the chains in the TMC, and correct any reported errors.
Reason:
The volume is removed from Catalog Control. The date value expressed by xxxxxxxxxx, rather than the normal expiration (run date plus R9 extension), is used. The value of xxxxxxxxxx is the highest expiration date found on the DSNB chain.
Action:
None. This is an informational message.
Reason:
TMSCTLG is unable to determine the catalog status of this data set. The specified CVOL return code or VSAM/ICF reason code is from the LOCATE macro. These data sets are not expired until corrective action is taken.
Action:
To determine the cause of the LOCATE error, see the IBM MVS Catalog Administration Guide or the Fujitsu Data Management Manual.
Reason:
Catalogs are offline.
Action:
No action is required. This is an informative message. TMSCTLG will not expire data sets.
Reason:
The listed data set was found in the OS catalog, however, the volume serial number it is cataloged to does not match the volume serial number of the TMC record.
Action:
No action is required. This is an informative message. TMSCTLG treats the TMC data set as an MVS catalog error and thus expires it.
Reason:
The listed data set was found in the OS catalog. However, the fileseq in the catalog does not match what is in the record.
Action:
None. This is an informational message. TMSCTLG treats the TMC data set as an MVS catalog error and expires it.
|
Copyright © 2013 CA Technologies.
All rights reserved.
|
|