Installing Your Product Using Pax ESD or DVD › Prepare the SMP/E Environment for a Pax Installation

Prepare the SMP/E Environment for a Pax Installation

The following steps describe the process to install products using native SMP/E JCL:

1. Download external HOLDDATA.
2. Allocate product data sets and SMP/E data sets.
3. Create an SMP/E environment.
4. Receive base functions and HOLDDATA.
5. Download and RECEIVE PTFs from http://ca.com/support.
6. Run an SMP/E APPLY CHECK operation.
7. Apply base functions using SELECT GROUPEXTEND.
8. Run an SMP/E ACCEPT CHECK operation.
9. Accept base functions using SELECT GROUPEXTEND.
10. Configure the product according to your site requirements.

Note: Steps 1 through 3 of this process are documented in detail in this section. Steps 4 through 9 are documented in the section describing how to run installation jobs for a Pax installation. If applicable to your product, Step 10 is documented in the section describing starting your product.

The members that are used in this procedure prepare the data sets, initialize the zones, and create the DDDEFs for your product.

Establishing a hierarchical file system (HFS) may be required as part of the product installation or required as a feature of the product.

For information about the members, see the comments in the JCL.

Follow these steps:

1. Customize the macro TMSSEDIT with your site-specific information and then copy the macro to your SYSPROC location. Replace the rightmost parameters for each ISREDIT CHANGE command. Each time you edit an installation member, type TMSSEDIT on the command line, and press Enter to replace the defaults with your specifications.

   The macro is ready to customize the yourHLQ.SAMPJCL members.

   Note: Set the DASD HLQ to the same value specified for yourHLQ within the JCL that is used to unzip the pax file.

   Note: The following steps include instructions to execute the TMSSEDIT macro each time you open a new SAMPJCL member. To edit all SAMPJCL members simultaneously, read and follow the instructions in the TMSAREAD member, and submit the TMSEDALL member.

2. Open the SAMPJCL member TMS1HOLD in an edit session and execute the TMSSEDIT macro from the command line.

   TMS1HOLD is customized.

3. Submit TMS1HOLD.

   This job downloads the error and FIXCAT HOLDDATA from http://ca.com/support.

4. Open the SAMPJCL member TMS2ALL in an edit session and execute the TMSSEDIT macro from the command line.

   TMS2ALL is customized.

5. Submit TMS2ALL.

   This job produces the following results:

   • The target and distribution data sets for your product are created.
   • Unique SMPLTS, SMPMTS, SMPSCDS, and SMPSTS data sets for this target zone are created.
6. If your product requires a USS file system or if you want to install a feature of the product that requires a USS file system, allocate and mount the file system:

   Note: You can customize the supplied HFS JCL to zFS, if your site requires it.

   1. Open the SAMPJCL member ccc2ALLU in an edit session and execute the TMSSEDIT macro from the command line.

      Note: All instances of ccc in this section indicate a three-character component code based on the FMID.

      ccc2ALLU is customized.

   2. Submit ccc2ALLU.

      This job allocates your HFS or zFS data sets.

   3. Open the SAMPJCL member ccc3MKD in an edit session and execute the TMSSEDIT macro from the command line.

      ccc3MKD is customized.

   4. Submit ccc3MKD.

      This job creates all directories and mounts the file system.

7. Open the SAMPJCL member TMS3CSI in an edit session and execute the TMSSEDIT macro from the command line.

   TMS3CSI is customized.

8. Submit TMS3CSI.

   This job produces the following results:

   • The CSI data set is defined.
   • The SMPPTS and SMPLOG data sets are allocated.
   • The global, target, and distribution zones are initialized.
   • The DDDEF entries for your product are created.
   • The DDDEFs for the required SMP/E data sets are created.
9. If your product requires HFS or if you want to install a feature of the product that requires HFS, add the DDDEFS that are required for the file system to your SMP/E environment:
   1. Open the SAMPJCL member ccc3CSIU in an edit session and execute the TMSSEDIT macro from the command line.

      ccc3CSIU is customized.

   2. Submit ccc3CSIU.

      This job customizes the CSI by adding the DDDEFs associated with the directory.