Self Monitoring › edgemon Utility--Monitor MIB Objects

edgemon Utility--Monitor MIB Objects

The edgemon command line utility automatically configures the SystemEDGE agent to monitor a MIB variable that you specify. With this utility, you specify the following:

• MIB variable, either by name or by object-identifier
• Threshold value and comparison operator
• Command
• Authentication
• Encryption
• Flags
• Description
• Object and severity information

The edgemon utility issues an SNMP Set request to create the appropriate entry in the target agent's Self Monitor table.

Use the edgemon utility as follows:

edgemon [-h hostname | ip_addr] [-p port] [-c community]
    [-v 1 | 2c | 3] [-u secName] [-s secLevel] [-n contextName]
    [-a authPassword] [-A MD5 | SHA]
    [-x privPassword] [-X DES | AES | 3DES]
    [-m FIPS_mode]
    [-t timeout] [-d logLevel] [-f logFile][-r retries]
    -o command

-h hostname | ipaddr

Specifies the host name or IP address of the system on which the agent is running. Accepts IPv4 and IPv6 addresses.

Default: localhost

-p port

Specifies the UDP port that the agent is running on (for example, 1691).

Default: 161

-c community

Specifies the read-write community string that the agent runs with. This option is valid for SNMPv1 and SNMPv2 only.

Default: public

-v {1 | 2c | 3}

Indicates the version of SNMP that the agent is running. Specify 1 for SNMPv1, 2c for SNMPv2c, or 3 for SNMPv3.

Default: 1

-u secName

Specifies the User-based Security Model (USM) user name used for SNMPv3 security.

Default: none

-s secLevel

Specifies one of the following security levels for SNMPv3 communication:

• 1 - noAuthNoPriv
• 2 - AuthNoPriv

3 - AuthPriv (SNMPv3 only)

-n contextName

Specifies the instance name for MIBMuxed agent.

Default: none

-a authPassword

Specifies the authentication password if the agent is configured for SNMPv3 with secLevel 2 (AuthNoPriv) or 3 (AuthPriv).

Note: This option is not required for SNMPv3 communication.

Default: none

-A {MD5 | SHA}

Specifies the authentication protocol to use if the agent is configured for SNMPv3 with secLevel 2 (AuthNoPriv) or 3 (AuthPriv). Currently only MD5 (Message Digest Algorithm) and SHA (Secure Hash Algorithm) are used.

Default: MD5

-x privPassword

Specifies the privacy (encryption) password if the agent is configured for SNMPv3 with secLevel 3 (AuthPriv).

Default: none

-X {DES | AES | 3DES}

Specifies the privacy protocol if the SNMPv3 user is configured with secLevel 3 (AuthPriv). Specify DES for Data Encryption Standard, AES for Advanced Encryption Standard using cryptographic keys of 128 bits (AES128), and 3DES for Triple Data Encryption Standard.

Default: none

-m FIPS_mode

Controls the FIPS mode of operation. Accepted values are 0, 1, and 2.

0

Indicates Non-FIPS mode.

1

Indicates FIPS co-existence mode.

2

Indicates FIPS only mode.

Default: 1

-r retries

Specifies the number of retries.

Default: 10

-t timeout

Specifies the duration before the SNMP receiver considers the request as timed out.

Default: 10 seconds

-d logLevel

Specifies the log level of the SNMP messages. Accepted values are 0 to 5.

0

Logs fatal messages.

1

Logs critical messages.

2

Logs warning messages.

3

Logs informational messages.

4

Logs all of the messages.

5

Logs all of the messages including debugging messages.

Default: 0

-f logfile

Specifies the name of the log file that contains error and debug information.

Default: sysedge_utility.log

-o command

Specifies the command and associated arguments. Supported commands include the following:

• oid (for monitoring an object)
• filesystem (for monitoring a file system)
• interface (for monitoring a network interface)
• cpu (for monitoring cpu)
• disk (for monitoring a disk)
• list (for listing the current Self Monitor table entries)
• setstatus (for setting the status of a Self Monitor table entry)
• delete (for deleting a Self Monitor table entry)

Note: For more information about supported commands, see edgemon Commands for Self Monitoring.