CICS Messages › CICS TS 3.1 and Later

CICS TS 3.1 and Later

The following messages are for CICS TS 3.1 and later environments:

TN0821W Specified COLLECT/RESET transaction tran points to non-CA MAT program. Default used.

Reason:

CICSOPTS parameter COLLECT_TRAN/RESET_TRAN is defined in CICS to execute a non-CA Mainframe Application Tuner program. Define the programs to be TCnnCREQ/TCnnCTUN.

Action:

Processing continues using the default transaction TUNC/TUNS.

Change the COLLECT/RESET transaction name to a different value that is not already defined. If the error persists, contact Customer Support.

Origin: TCnnTDQR

TN0823I CA MAT exitname user exit program loaded at: address

Reason:

Issued during PLTPI processing and if exit program is restarted using TUNS (see the Installation Guide).

Action:

Processing continues. Information message only.

Origin: TCnnENAB

TN0824I CA MAT COLLECT transaction=____

Reason:

Indicates the Summary Statistics Collection Transaction name. This name is specified in the CICSOPTS parameter member as COLLECT_TRAN =. The default is TUNC.

Action:

None.

Origin: TCnnTDQR

TN0825W INQUIRE TRANSACTION failed for tran. Default name will be used.

Reason:

Indicates that the specified COLLECT/RESET transaction does not point to the correct program.

Action:

Processing continues using the default transaction TUNC/TUNS.

Change the CICSOPTS parameter COLLECT_TRAN/RESET_TRAN to a different name. The name must follow standard CICS conventions and must not start with C.

If this message persists, contact Customer Support.

Origin: TCnnTDQR

TN0826W Invalid COLLECT/RESET transaction name tran. Default name will be used.

Reason:

The specified COLLECT/RESET transaction has an invalid name. The name must follow standard CICS conventions and must not start with C.

Action:

Processing continues using the default transaction TUNC/TUNS.

Change the CICSOPTS parameter COLLECT_TRAN/RESET_TRAN to a different name. The name must follow standard CICS conventions and must not start with C.

Origin: TCnnTDQR

TN0827I CA MAT exitname user exit program disabled

Reason:

Issued during TUNS processing if an exit program is to be disabled (see the Installation Guide).

Action:

Processing continues. Information message only.

Origin: TCnnENAB, TCnnDSAB

TN0828W Unable to disable the exitname user exit program

Reason:

This message is issued during TUNS processing if an exit program is to be disabled (see the Installation Guide). The program was already disabled or was never enabled.

Action:

Processing continues. If this problem persists, contact Customer Support.

Origin: TCnnDSAB

TN0829E Unexpected condition occurred during request

Reason:

An abend has occurred during PLTPI processing.

Action:

A transaction dump is issued with dumpcode TNE1 and further processing is terminated. Attempting to use functionality has unpredictable results. Contact Customer Support.

Origin: TCnnFSET

TN0830I CA MAT program global workarea at: address

Reason:

Issued during PLTPI processing when an exit program is enabled.

Action:

Processing continues. Information message only.

Origin: TCnnENAB

TN0831S INQUIRE error for default COLLECT transaction TUNC. Processing terminated.

Reason:

Indicates that the default COLLECT transaction name TUNC has been selected, but the transaction does not point to the correct program. This message appears if a transaction named TUNC already exists.

Action:

Processing is terminated. Change the CICSOPTS parameter COLLECT_TRAN to a different name. The name must follow standard CICS conventions and must not start with C.

Origin: TCnnTDQR

TN0832E Unable to obtain the ICMP

Reason:

Issued when an exit program attempts unsuccessfully to obtain this control block.

Action:

Functionality is disabled.

This message can be due to lack of EDSA storage. If the problem persists when the amount of storage is increased, contact Customer Support.

Origin: TCnnCMPX, TCnnCSTO, TCnnICMT

TN0833S Unable to install CA MAT exit program

Reason:

Issued during PLTPI processing or TUNS processing when CA Mainframe Application Tuner detects one of the following conditions:

• An unsupported CICS release
• CICS is not in the correct state for this type of processing

This message is followed by either message TN0837S (invalid CICS version) or TN0860S (invalid CICS status).

Action:

Functionality is disabled.

Verify the CICS release. Currently only CICS TS 3.1 and later is supported for this type of functionality. If the problem persists, contact Customer Support.

Origin: TCnnENAB, TCnnFSET

TN0834S CREATE failed for transaction tran.

Reason:

An error occurred when CA Mainframe Application Tuner was attempting to create the specified transaction.

Action:

CICS summary statistics are not collected. If this error persists, contact Customer Support.

Origin: TCnnCRTE

TN0835W Unsupported DB2 release

Reason:

During monitor initialization, it was determined that the target address space was indeed a DB2 address space but that the version/release is no longer supported.

Action:

The monitor continues to completion as if the address space was a normal non-DB2 address space.

Not applicable; this DB2 version/release is not supported.

Origin: TNEXLDB

TN0836S Invalid CICS status - NOT STARTUP. Program TCnnCPLT

Reason:

CICS is not completely ACTIVE when TCnnCPLT is executed.

Action:

Functionality is disabled. If this error persists, contact Customer Support.

Origin: TCnnCPLT

TN0837S Unsupported CICS version version

Reason:

Issued during PLTPI processing or TUNS processing when CA Mainframe Application Tuner detects an unsupported CICS release.

Action:

Functionality is disabled.

Verify the CICS release. Currently only CICS TS 3.1 and later is supported for this type of functionality. If the problem persists, contact Customer Support.

Origin: TCnnCPLT, TCnnCRTE, TCnnCTUN, TCnnDSAB, TCnnENAB, TCnnEXBG, TCnnFSET, TCnnTDQ, TCnnTDQR

TN0838S Can't link to program program

Reason:

Issued by various CICS modules for a CICS LINK failure. Followed by message TN0851I containing RESP, RESP2, EIBFN.

Action:

Further use of functionality has unpredictable results.

This error is possibly an installation error. Verify that CA Mainframe Application Tuner has been correctly installed. If the problem persists, contact Customer Support.

Origin: All CICS modules

TN0839S Default COLLECT transaction tran incorrectly defined. Processing terminated.

Reason:

Indicates that the default COLLECT transaction name TUNC has been selected, but the transaction does not point to the correct program. This error occurs if a transaction named TUNC already exists.

Action:

Processing is terminated.

Change the CICSOPTS parameter COLLECT_TRAN to a different name. The name must follow standard CICS conventions and must not start with C.

Origin: TCnnTDQR

TN0840S Unable to load program program, resp=resp, resp2=resp2

Reason:

Issued during PLTPI processing or TUNS processing when an error occurs during load of a program.

Action:

Functionality is disabled.

Check the CICS log for any associated error conditions. This error is possibly an installation error (such as a missing CSD definition or load module). If the problem persists, contact Customer Support.

Origin: TCnnENAB

TN0844E Tran table entry not found. Unable to collect statistics.

Reason:

The Transaction Activity table used by CA Mainframe Application Tuner to locate the CICS monitoring control block structure is not available.

Action:

Functionality is disabled. If the problem persists, contact Customer Support.

Origin: TCnnCSTO

TN0845W Incorrect CICS monitoring setting, perf= ___, exception= ___, monitoring= ___.

Reason:

To collect CICS transaction and summary statistics, the following System Initialization Table (SIT) parameters must be set:

Action:

Processing continues. It is possible that CICS transaction and summary statistics are not available.

See the Installation Guide for information about changing the SIT parameters.

Origin: TCnnENAB

TN0846I CICS requested statistics were generated. Last reset at hh:mm:ss.

Reason:

Issued at normal completion of TUNC processing (obtain requested statistics).

Action:

Processing continues. Information message only. The reset time is displayed on CICS Summary Statistics analysis panels.

Origin: TCnnCREQ

TN0847W CICS requested statistics were generated - some were not available. Last reset at hh:mm:ss.

Reason:

Issued at normal completion of TUNC processing (obtain requested statistics). Some statistics were not available because the relevant CICS functionality (such as program autoinstall) has not been activated.

Action:

Processing continues. When CICS Summary Statistics analysis panels are displayed, statistics for the disabled functions will show NO DATA.

Origin: TCnnCREQ

TN0848I Summary statistics collection set to manual

Reason:

Indicates the Summary Statistics Collection interval is set to 0 manual. This is specified in the CICSOPTS parameter member as COLLECT=0 . The COLLECT transaction will not run automatically, but can be run manually.

Action:

Processing continues. Information message only.

Origin: TCnnTDQR

TN0849S START error for tran transaction. Summary statistics cannot be collected.

Reason:

There was an error detected when starting the COLLECT transaction after the specified interval (specified in CICSOPTS parameter member). Summary statistics are not collected for the interval.

Action:

Processing continues. If this persists, contact Customer Support.

Origin: TNnnCREQ, TCnnENAB

TN0850S text

Reason:

Issued by the CICS message module for various internal error conditions.

Action:

Functionality is disabled. Contact Customer Support.

Origin: TCnnCMSG

TN0851I RESP=resp, RESP2=resp2, EIBFN=eibfn

Reason:

Always follows a preceding message. Issued by the CICS message module when the calling module requests display of CICS diagnostics (or if the message module has a CICS error).

Action:

According to the preceding message. Supply a copy of this message if you when contacting Customer Support.

Origin: TCnnCMSG

TN0852S error in message handler, rc=rc

Reason:

This error is issued as an operator message by the calling program when the CICS message module has encountered a serious error.

Action:

Further use of functionality has unpredictable results.

This is probably an installation error. Verify that CA Mainframe Application Tuner has been correctly installed. If the problem persists, contact Customer Support.

Origin: All CICS modules

TN0860S Invalid CICS status - status, program=program

Reason:

Issued during PLTPI processing or TUNS processing when the status of CICS is not valid for the function requested (such as PLTPI processing at shutdown).

Action:

Functionality is disabled.

If this message occurs during PLTPI processing, contact Customer Support. If it occurs during TUNS processing, check that this command has been issued correctly (that is, when CICS is active). If the problem persists, contact Customer Support.

Origin: TCnnCTUN, TCnnDSAB, TCnnENAB, TCnnEXBG, TCnnFSET

TN0861S Can't enable exit program program, RESP=resp, RESP2=resp2

Reason:

Issued during PLTPI processing or TUNS processing when an exit program cannot be enabled due to a CICS error.

Action:

Functionality is disabled. This error is probably an installation error (such as a missing CSD definition or missing module). If the problem persists, contact Customer Support.

Origin: TCnnENAB

TN0862S INQUIRE TDQ error for tdq

Reason:

Issued during PLTPI processing or TUNS processing when the TDQ is being created/checked. This error is followed by message TN0851 (RESP, RESP2 codes).

Action:

Functionality is disabled.

Verify that the //TRITUNE DD CARD is present in the CICS JCL. If the problem persists, contact Customer Support.

Origin: TCnnTDQ

TN0863S TDQ tdq is invalid

Reason:

Issued during PLTPI processing or TUNS processing when the existing transient data queue is being verified. There is an error in the TDQ configuration.

Action:

Functionality is disabled. Contact Customer Support.

Origin: TCnnTDQ

TN0864S CREATE failed for TDQ tdq

Reason:

Issued during PLTPI processing or TUNS processing when the TDQ CREATE fails due to a CICS error. This error is followed by message TN0851 (RESP, RESP2 codes).

Action:

Functionality is disabled.

Verify that the //TRITUNE DD CARD is present in the CICS JCL. If the problem persists, contact Customer Support.

Origin: TCnnCRTE

TN0865W Incorrect TDQ specified, default tdq set

Reason:

The override input parameter TDQ name specified in the CICS INITPARM is invalid (see the Installation Guide).

Action:

Processing continues with the default TDQ name TRIT. There will be unpredictable results if another (non-CA Mainframe Application Tuner) TDQ exists with this name.

Verify that the supplied TDQ name has valid syntax and follows the syntax specified in the Installation Guide. If the problem persists, contact Customer Support. If you are happy with the default TDQ name, you do not need to supply the INITPARM parameter.

Origin: TCnnTDQ

TN0866I Override TDQ name tdq specified

Reason:

The override input parameter TDQ name specified in the CICS INITPARM is used for PLTPI/TUNS processing.

Action:

Processing continues.

Information message only. Unpredictable results are possible if another (non-CA Mainframe Application Tuner) TDQ exists with this name.

Origin: TCnnTDQ

TN0867W Invalid value specified for COLLECT (nnn), default value (1) will be set

Reason:

The value for the collection frequency is invalid. This is specified in the CICSOPTS parameter member as COLLECT=. Valid values are 0 to 60 (minutes).

Action:

The default value of 1 minute will be used.

Set the CICSOPTS COLLECT parameter to a numeric value
between 1 and 60.

Origin: TCnnTDQR

TN0868W OPEN failed for CA MAT TDQ tdq. Default parameters will be set.

Reason:

There was an error opening the TDQ.

Action:

Processing continues using default parameters.

For information about defining the CICSOPTS member to CICS, see the "Define CICS Support" section of the Installation Guide . If this error persists, contact Customer Support.

Origin: TCnnTDQR

TN0869S READQ failed for TDQ tdq

Reason:

Issued during PLTPI processing or TUNS processing when a READQ TD fails due to a CICS error.

It is followed by message TN0851 (RESP, RESP2 codes).

Action:

Functionality is disabled.

Check that the //TRITUNE DD CARD is present in the CICS JCL. If the problem persists, contact Customer Support.

Origin: TCnnTDQR

TN0870I Summary CICS statistics option set to ________.

Reason:

Indicates if CICS summary statistics are to be collected (YES/NO). The default value is YES, and currently cannot be changed.

Action:

None.

Origin: TCnnTDQR

TN0871W Invalid value specified for MAXTRANS, (nnnn), default value (2000) will be set.

Reason:

This message can be issued during CICS parameter processing (see the Installation Guide for description).

Action:

Processing continues. Correct the MAXTRANS value (or leave it to default). If the problem persists, contact Customer Support.

Origin: TCnnTDQR

TN0872I MAXTRANS value set to value

Reason:

Indicates the value for the maximum number of entries in the transaction table (1 to 9999). This value is specified in the CICSOPTS parameter member as MAXTRANS=. The default is 2000.

Action:

None.

Origin: TCnnTDQR

TN0873W SUMMARY=NO specified and/or stats exit not active

Reason:

This message is issued during TUNC processing (collect CICS requested statistics) if statistics collection is off (SUMMARY=NO) or if the summary statistics collection exit program is not active (see the Installation Guide).

Action:

TUNC processing terminates. The Summary Statistics analysis options will return NO DATA if no previous TUNC processing has been successful.

Check that you have supplied the appropriate CICS parameters (see the Installation Guide).

Origin: TCnnCREQ

TN0874W Work table full for INC|EXC

Reason:

This message is issued during PLTPI/TUNS processing if you have supplied more than the maximum (100) number of either EXC or INC cards in the CICS startup options (see the Installation Guide).

Action:

Processing continues. Any cards beyond the specified limit will be ignored.

If you have supplied a valid number of INC or EXC cards (0 <= n <= 100), contact Customer Support.

Origin: TCnnTDQR

TN0875I Enable bypassed for exit program program

Reason:

This message is issued during TUNS processing if the CICS parameters imply enable of an exit program and that program is already enabled.

Action:

Processing continues. Information message only.

Origin: TCnnENAB

TN0876I Summary statistics collection frequency set to ____ minute(s)

Reason:

Indicates the value for the statistics collection frequency. This value is specified in minutes (0 to 60). 0 means that summary statistics collection is OFF . This is specified in the CICSOPTS parameter member as COLLECT=. The default is 1.

Action:

None.

Origin: TCnnTDQR

TN0877S Serious CICS error for program program

Reason:

This message is issued during TUNS processing when the specified program encounters an unrecoverable CICS error.

It is followed by message TN0851 (RESP, RESP2, EIBFN codes).

Action:

Further use of functionality will have unpredictable results.

Check the CICS log for possible CICS error conditions. Also check that CA Mainframe Application Tuner has been correctly installed. If the error persists, contact Customer Support.

Origin: TCnnCREQ, TCnnCTUN

TN0878S CA MAT TDQ not found for DDNAME TRITUNE

Reason:

This message is issued during TUNS processing when the TDQ cannot be found.

Action:

Further use of functionality will have unpredictable results. Check the CICS log for possible CICS error conditions. Also check that CA Mainframe Application Tuner has been correctly installed (TRITUNE DD card must be present in CICS JCL). If the error persists, contact Customer Support.

Origin: TCnnCTUN

TN0879S Option refresh terminated for program program

Reason:

This message is issued during TUNS processing when a serious error condition occurs. A preceding message will have been issued.

Action:

Further use of functionality will have unpredictable results.

Refer to preceding error message.

Origin: TCnnCTUN

TN0880I CA MAT/CICS options successfully refreshed

Reason:

This is the last of a series of normal messages issued during TUNS processing (see the Installation Guide for explanation).

Action:

Processing continues. Information message only.

Origin: TCnnCTUN

TN0881W Exit program exitname already enabled for exit point exit point

Reason:

When attempting to load the exit program, it was found to be enabled.

Action:

Processing continues.

Origin: TCnnENAB

TN0882I CA MAT monitoring ON

Reason:

Indicates that CICS monitoring is activated. This is specified in the CICSOPTS parameter member as MONITOR=. The default is YES.

Action:

None.

Origin: TCnnTDQR

TN0883W CA MAT monitoring OFF. Use TUNS transaction to restart.

Reason:

This is one of a series of normal messages which might be issued during PLTPI or TUNS processing (see the Installation Guide for explanation).

Action:

Processing continues. Functionality is disabled. Information message only.

Origin: TCnnTDQR

TN0884W Exit program program already disabled for exit point exit point

Reason:

This message is issued during TUNS processing if the CICS parameters imply disable of an exit program and that program is already disabled.

Action:

Processing continues. The specified functionality has already been disabled. Information message only.

Origin: TCnnDSAB

TN0888S CA MAT XMNOUT exit program program not active. COLLECT processing terminated.

Reason:

This message is issued during TUNC processing (collect CICS requested statistics) if the summary statistics collection exit program is not active (see the Installation Guide).

Action:

TUNC processing terminates. The Summary Statistics analysis options will return NO DATA if no previous TUNC processing has been successful.

Check that you have supplied the appropriate CICS parameters (see the Installation Guide). If this error persists, contact Customer Support.

Origin: TCnnCREQ

TN0889S Invalid object type ________ for CREATE. CREATE processing terminated.

Reason:

When creating a CICS object, an invalid object type was encountered. Valid types are TRAN and TDQ.

Action:

Processing is terminated. If this error persists, contact Customer Support.

Origin: TCnnCRTE

TN0890I CA MAT RESET transaction= ___

Reason:

Indicates the name for the Reset Parameters Transaction.
This is specified in the CICSOPTS parameter member as RESET_TRAN. The default is TUNS.

Action:

None.

Origin: TCnnTDQR

TN0891S Default RESET transaction tran incorrectly defined. Processing terminated.

Reason:

The default RESET transaction TUNS may already be defined.
This transaction is not pointing to the correct program.

Action:

Processing is terminated. Change the CICSOPTS parameter RESET_TRAN to a different name. The name must follow standard CICS conventions and must not start with C.

Origin: TCnnTDQR

TN0892S INQUIRE error for default RESET transaction TUNS. Processing terminated.

Reason:

Indicates that the default RESET transaction name TUNS has been selected, but the transaction has not been defined or defined incorrectly.

Action:

Processing is terminated. Change the CICSOPTS parameter RESET_TRAN to a different name. The name must follow standard CICS conventions and must not start with C.

Origin: TCnnTDQR

TN0893I TRITUNE DD card not present. Default parameters will be set.

Reason:

The TRITUNE DD statement could not be found in the CICS JCL.

Action:

See the "Define CICS Support" section of the Installation Guide for information about defining the CICSOPTS member to CICS.

Origin: TCnnTDQR

TN0894W Field=aaaaa accumulation over maximum value. TRAN=bbbb

Reason:

This message indicates that an internal counter aaaaa is greater than or equal to X'FFFFFFFF' for transaction bbbb.

This situation can occur when a CICS transaction is run very frequently without being monitored by CA Mainframe Application Tuner.

Action:

None.

Origin: TCnnCMPX

TN8887S Cannot link to program TCnnCPLT

Reason:

Cannot link to program TCnnCPLT where nn is the CICS release number. For example, o nn = 64 for CTS 3.1 and o nn = 65 for CTS 3.2.

Action:

Make sure TCnnCPLT is in one of the CICS DFHRPL DD linklib statements.

Origin: TC00CPLT

TN8888S UNABLE TO FIND TC00FSET

Reason:

Cannot find program TC00FSET.

Action:

Make sure TC00FSET is in one of the CICS DFHRPL DD linklib statements.

Origin: TC00CPLT