Appendix A. MESSAGES
This appendix lists all messages generated by the CA MICS Web
Analyzer. The messages are printed on both the MICSLOG and
SAS log data sets. When reviewing the output of a job, first
look at the MICSLOG data set because it contains fewer lines
of information, making it easier to see whether or not a job
or job step completed as expected. If the MICSLOG message
does not provide enough information, consult this appendix
for more information about the message. If you still need
more information, consult the SAS log to help debug the
problem.
The messages are listed in ascending numerical sequence and
include the full text of the message, the type, the reason
for the message, appropriate user action, and applicable
references to documentation.
The format of a MICSLOG message is:
hh:mm:ss.hs cccnnnnns ttttttttttttttttttttttttttttttttttt
where
hh:mm:ss.hs is the time that the message was issued.
cccnnnnns is the message identifier. The message
identifier consists of three parts:
ccc three letter product identifier
nnnnn the message number
s the severity identifier, where I is
an informational message, W indicates
a warning, and E indicates an error
ttt...ttt is the message text. If the text spans more
than one line, the message identifier is
repeated.
The remainder of this appendix shows the MICSLOG messages
produced for the CA MICS Web Analyzer. In addition to the
message identifier and text, this section presents the reason
for the message, suggests actions to take to resolve the
problem, and refers you to additional sources of information
to help you understand the problem and its resolution.
+----------+
| WEB00100 |
+----------+
TEXT: Starting DELTA PROCESS for: %FILENAME
TYPE: Informational
REASON: Many of the WebSphere data elements read from
the raw data are accumulated values since the
server started. This message indicates that
the delta routines are about to be entered
for the file listed. When done, MICSLOG
message WEB00199 is displayed.
ACTION: None
REFERENCES: None
+----------+
| WEB00102 |
+----------+
TEXT: Suspend record deleted due to age:
SYSID=%SYSID; WEBIP=%WEBIP; ENDTS=%ENDTS;
WEBSUSCT=%SUSLIMIT
TYPE: Informational
REASON: Suspend records are deleted from the suspend
file for web servers (identified uniquely by
WEBIP and WEBPORT) not encountered for the
number of days defined by the SUSLIMIT
(default 7) statement in
prefix.MICS.PARMS(WEBOPS). Suspend records
hold the values last encountered for a WEBIP
in the DAILY update and are used to
initialize the lag variables for delta
calculations during the next DAILY run. Web
server observations not encountered again for
the default of 7 days are dropped from the
suspend (WEB_WP) file.
ACTION: None
REFERENCES: None
+----------+
| WEB00106 |
+----------+
TEXT: No suspend record for: SYSID=%SYSID;
WEBIP=%WEBIP ENDTS=%ENDTS WEBPORT=%WEBPORT
TYPE: Informational
REASON: No suspend record was found to initialize
lag variables for delta calculations. The
WEBIP is probably new. Delta processing is
skipped for the first record.
ACTION: None
REFERENCES: None
+----------+
| WEB00110 |
+----------+
TEXT: More than one day exists between current and
previous suspend records:
SYSID=%SYSID; WEBIP=%WEBIP; ENDTS=%XENDTS
LAGENDTS=%XLAGTS;
FILE00=%FILE00 SUSPEND=%SUSPEND
WEBPORT=%WEBPORT
TYPE: Warning
REASON: The difference between ENDTS on the current
record and the previous record is greater
than 24 hours.
ACTION: Determine if this gap in data is correct or
if data was missing from SMF. Data does not
exist unless the WEB Server was active (up
and running) and recording to SMF. If data
was missing but is available, you may want
to restore the unit database and rerun the
daily process with all the input data.
REFERENCES: None
+----------+
| WEB00111 |
+----------+
TEXT: One or more data elements contained a missing
value: FILE=%FILE
This may be normal if the data element is
inactive in WEBGENIN or unavailable at this
WEB release.
Refer to the SASLOG for the specific data
elements.
TYPE: Warning
REASON: Either the temporary variable used to hold
the previous observation's value or the
current observation contains a missing value.
ACTION: This condition may be normal either if the
variable is not available at the release of
WebSphere that you are processing, or if the
data element has been deactivated in
WEBGENIN. Determine which it is, and if this
field is available and you require it,
activate it.
REFERENCES: None
+----------+
| WEB00112 |
+----------+
TEXT: During DELTA PROCESSING, at least one data
element would have received a negative value.
Data element value set to 0. FILE=%FILE',
Refer to the SASLOG for the specific data
element.
TYPE: Warning
REASON: The reason depends on the file noted in the
message text, but is the result of the
preceding observation containing a value
greater than that in the current observation,
which is unexpected in cumulative records.
ACTION: This could happen if there was a break in the
raw input data and the web server had been
restarted. In this case, if the missing data
contained the SMF 103 subtype 1 configuration
record, the processing would not have been
triggered and the counters would have been
reset. Ensure that there were no breaks of
time period in the raw input data.
REFERENCES: None
+----------+
| WEB00121 |
+----------+
TEXT: SMF type 120 subtype 6 and/or subtype 8
records not processed. You must be at SAS
8.02 or higher to process these records.
This unit is configured to run with SAS
release %VR .
Total number of records rejected:
Subtype 6 ===>
Subtype 8 ===>
TYPE: Warning
REASON: This is to bring user attention to the fact
that the records listed for subtype 6 and/or
subtype 8 are rejected because the unit is
configured with the SAS release that does not
support an informat $UCS2Xw. This format is
used to read raw data that is in unicode
format.
ACTION: Upgrade your SAS system software in this unit
to SAS 8.02 or higher.
REFERENCES: None.
+----------+
| WEB00125 |
+----------+
TEXT: %LINE
TYPE: Informational
REASON: To show all the keywords and their values
that are in effect for the WEBPGEN run.
ACTION: Print the contents of the PARM member.
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00126 |
+----------+
TEXT: %SRVNAME - The server name (WEBNAME) is set
to the concatenation of WEBIP/WEBPORT.
Assign user defined values for WEBNAME,
WEBSNAME, and WEBGROUP for this server by
updating: prefix.MICS.PARMS(WEBSLIST). Then
submit prefix.MICS.CNTL(WEBPGEN).'
TYPE: Informational
REASON: To display prefix.MICS.PARMS(WEBOPS)
statements in MICSLOG when
prefix.MICS.CNTL(WEBPGEN) is executed to
generate product unit level code.
ACTION: None
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00128 |
+----------+
TEXT: %TOKEN1 KEYWORD value not coded. Set to
DEFAULT of 7.
TYPE: Informational
REASON: The keyword has a missing parameter value. A
default value of 7 is automatically selected
for this parameter. This message is issued if
the keyword is coded without the parameter
value.
ACTION: Code a value between 1 and 7 and resubmit
prefix.MICS.CNTL(WEBPGEN).
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00129 |
+----------+
TEXT: %TOKEN1 KEYWORD value out of range. Must be
from 1 to 7.
TYPE: Error
REASON: The keyword contains a suspend value that is
used to determine whether a suspended
observation is dropped or kept. This message
is issued if the value falls outside the
range of 1 to 7. The job is terminated.
ACTION: Code a value between 1 and 7. Resubmit
prefix.MICS.CNTL(WEBPGEN).
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00130 |
+----------+
TEXT: Errors found in prefix.MICS.PARMS(WEBOPS).
Correct all errors noted in MICSLOG.
Then RESUBMIT prefix.MICS.CNTL(WEBPGEN).
TYPE: Error
REASON: One or more of the keywords (CFGLIMIT,
WCFLIMIT, and SUSPEND) contain an out-of-
range (less than 1 or greater than 7) value
that caused the job to terminate.
ACTION: Code a desired value for all the keywords in
error and resubmit prefix.MICS.CNTL(WEBPGEN).
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00131 |
+----------+
TEXT: GMTOFF for orgsysid %GMTORG is already
defined. Duplicate statement not permitted.
TYPE: Error
REASON: The orgsysid for a GMTOFF statement was
already used on an earlier GMTOFF statement.
Only one time offset may be specified for a
particular system.
ACTION: Delete or modify the statement as desired and
resubmit prefix.MICS.CNTL(WEBPGEN).
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00132 |
+----------+
TEXT: Missing arguments in above line. GMTOFF
statement must be followed by two arguments:
1-an orgsysid value, and 2-a time offset.
TYPE: Error
REASON: The GMTOFF statement keyword must be followed
by exactly two arguments: an orgsysid value
and a time offset. At least one of these was
missing from the line displayed immediately
above the MICSLOG message.
ACTION: Delete or modify the statement as desired and
resubmit prefix.MICS.CNTL(WEBPGEN).
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00133 |
+----------+
TEXT: GMTOFF / orgsysid ARRAY size exceeded.
Current ARRAY size: %CKPTCNT
Array size controlled by CKPTCNT statement in
prefix.MICS.PARMS(SITE)
TYPE: Error
REASON: The capacity of the internal array used to
hold the time offsets for each orgsysid
listed in GMTOFF statements was exceeded.
ACTION: The current array size is listed in the
message. It can be altered by changing the
value of the CKPTCNT statement in
prefix.MICS.PARMS(SITE). Either increase the
CKPTCNT size, or code fewer GMTOFF statements
than the array capacity.
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00134 |
+----------+
TEXT: GLOBAL statement not followed by recognized
keyword. Invalid keyword: %GTOKEN2'
TYPE: Error
REASON: The GLOBAL statement can only be followed by
specific keywords, such as GMTOFF.
ACTION: Delete or modify the statement by using a
valid GLOBAL statement keyword. Then
resubmit prefix.MICS.CNTL(WEBPGEN).
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00135 |
+----------+
TEXT: GLOBAL GMTOFF statement must be followed by a
numeric time offset.
TYPE: Error
REASON: The argument following the GLOBAL GMTOFF
statement must be a numeric time offset.
Either blanks or a non-numeric argument was
used instead of a numeric time offset.
ACTION: Delete or modify the statement by adding a
numeric time offset value after GLOBAL
GMTOFF. Then resubmit
prefix.MICS.CNTL(WEBPGEN).
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00136 |
+----------+
TEXT: Time Offset value is invalid in above line.
Code a value in the range of -13 to +13.
TYPE: Error
REASON: The time offset value coded in the statement
immediately above the MICSLOG error message
is out of the allowable range of -13 to +13.
ACTION: Delete or modify the statement by adding or
correcting the keyword's time offset value.
Then resubmit prefix.MICS.CNTL(WEBPGEN).
+----------+
| WEB00137 |
+----------+
TEXT: Undefined orgsysid value: %ORGSYSID
on the above GMTOFF statement is not defined
in prefix.MICS.PARMS(SYSID)
or sharedprefix.MICS.PARMS(CPLXSID).
TYPE: Error
REASON: The orgsysid value shown in the error message
was not defined at the unit or complex level.
ACTION: Delete the statement or add the orgsysid to
either prefix.MICS.PARMS(SYSID) or
sharedprefix.MICS.PARMS(CPLXSID). Then
SUBMIT prefix.MICS.PARMS(BASPGEN). When
complete, resubmit prefix.MICS.CNTL(WEBPGEN).
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00138 |
+----------+
TEXT: Only one GLOBAL GMTOFF statement permitted.
Duplicate statements found.
TYPE: Error
REASON: Only one GLOBAL GMTOFF statement is
allowed.
ACTION: Delete the duplicate statement and resubmit
prefix.MICS.CNTL(WEBPGEN).
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00139 |
+----------+
TEXT: GMTOFF statement must be followed by an
orgsysid value of 4 bytes or less.
%GTOKEN2 found instead.
TYPE: Error
REASON: The orgsysid value coded on the GMTOFF
statement cannot exceed four bytes in length.
The erroneous orgsysid is listed with the
message.
ACTION: Delete the statement or modify the orgsysid
value. Resubmit prefix.MICS.CNTL(WEBPGEN).
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00140 |
+----------+
TEXT: %LINE
No value was coded for the required IP
ADDRESS/PORT number field (COLS 4-28).
Statement is ignored.
TYPE: Warning
REASON: IP ADDRESS/PORT NUMBER column in the
statement is not specified. This is the
highest level of information required to
identify unique observations in the data. In
the absence of this value, all other values
specified are meaningless and ignored.
ACTION: Specify the IP ADDRESS/PORT NUMBER that is
associated with other specified values and
resubmit prefix.MICS.CNTL(WEBPGEN).
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00141 |
+----------+
TEXT: %IP_PORT
Duplicate IP ADDRESS/PORT values detected.
Only one entry per IP ADDRESS/PORT value
allowed.
Duplicate IP ADDRESS/PORT values must be
deleted.
TYPE: Error
REASON: Multiple IP ADDRESS/PORT values detected.
ACTION: Delete duplicated IP ADDRESS/PORT values and
resubmit prefix.MICS.CNTL(WEBPGEN).
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00145 |
+----------+
TEXT: %LINE
IP ADDRESS/PORT value coded, but no values
coded for optional fields.
Statement is ignored.
TYPE: Warning
REASON: At least one of the optional values must be
coded for the IP ADDRESS/PORT entry column to
have any meaning. The absence of any values
in optional fields results in blank values
for WEBSNAME, WEBGROUP, and WEBNAME elements
in the database files. These database
elements will be blank if no IP ADDRESS/PORT
entry is present in
prefix.MICS.PARMS(WEBSLIST).
ACTION: 1. Remove the entry
2. Define at least one value in one of the
columns after IP ADDRESS/PORT column.
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00148 |
+----------+
TEXT: Errors found in prefix.MICS.PARMS(WEBSLIST).
Correct all errors noted in MICSLOG.
Then RESUBMIT prefix.MICS.CNTL(WEBPGEN).
TYPE: Error
REASON: There are errors in
prefix.MICS.PARMS(WEBSLIST).
ACTION: Correct all errors noted in MICSLOG and
resubmit prefix.MICS.CNTL(WEBPGEN).
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00150 |
+----------+
TEXT: %LINE
No value coded for element(s): %BLANKFLD
These element(s) will contain blank values in
the WLG INFORMATION AREA files.
TYPE: Warning
REASON: WEBSNAME (Short name), WEBGROUP (group name),
and/or WEBNAME (Web Server Name) parameters
were detected with no values specified. The
message echoes these parameters for your
information. If you choose to take no
action, you will see blank values in
corresponding fields in the CA MICS Web
Analyzer files.
ACTION: Optional. Enter valid values for the listed
parameters and resubmit
prefix.MICS.CNTL(WEBPGEN).
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00199 |
+----------+
TEXT: Ending DELTA PROCESS for: %FILENAME
LAG RELOADS : %RELOADS
SUSPEND RECORDS AGED : %SUSDELS
MISSING SUSPEND RECORDS : %MISSSUSP
TYPE: Informational
REASON: Informational processing summary statistics.
ACTION: None
REFERENCES: None
+----------+
| WEB00210 |
+----------+
TEXT: Host name or IP Address 2 (SALHSTI2) contains
non-blank value displayed below:
%SALHSTI2
The element SALHSTI2 is inactive. Please
review the product guide, Section 5.3.1.3, to
determine the corrective actions required.
TYPE: Warning
REASON: SALHSTIP element is active. While SALHSTI2
is inactive, the DAILY processing has
detected a nonblank value in the element. If
you use the SALHSTIP element for analysis,
you should consider activating the SALHSTI2
element. Please see the discussion in the
WLGSAL file Usage Consideration section
5.3.1.3.
ACTION: Activate the SALHSTI2 element as required.
Activating this element is at the user's
discretion.
REFERENCES: See dictionary elements SALHSTIP and
SALHSTI2.
+----------+
| WEB00211 |
+----------+
TEXT: Host name or IP Address 2 (RFLHSTI2) contains
non-blank value displayed below:
%RFLHSTI2
The element, RFLHSTI2 is inactive.
TYPE: Warning
REASON: RFLHSTIP element is active. While RFLHSTI2
is inactive, the DAILY processing has
detected a nonblank value in the element. If
you use the RFLHSTIP element for analysis,
you should consider activating the RFLHSTI2
element. Please see the discussion in the
WLGRFL file Usage Consideration section
5.3.3.3.
ACTION: Activate the RFLHSTI2 element as required.
Activating this element is at the user's
discretion.
REFERENCES: See dictionary elements RFLHSTIP and
RFLHSTI2.
+----------+
| WEB00250 |
+----------+
TEXT: *********************************************
*********************************************
WLE LOG records were detected but NOWLG
OPTION is in effect. All log data discarded.
See Section 7.1 for more information.
*********************************************
*********************************************
TYPE: Warning
REASON: The INPUTWEB DD contains a data set with
records, but NOWLG options are in effect for
the WEB product.
ACTION: Edit sharedprefix.MICS.GENLIB(WEBGENIN) and
change parameter value from NOWLG to WLG on
the OPTION statement.
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00251 |
+----------+
TEXT: +---+----+----+----+----+----+----+----+----+
A Total of %WRK_NWEB non-WEB related SMF
records found in input, and discarded.
+---+----+----+----++---+----+----+----+----+
TYPE: Informational
REASON: The INPUTSMF DD refers to a dataset that
contains SMF records other than type 103s.
ACTION: Consider activating DAYSMF step or any other
utility at your disposal to preprocess SMF
data to extract SMF type 103 records in a
dataset that contains type 103 records only.
This improves DAY052 processing time.
REFERENCES: Chapter 7 in this guide.
+----------+
| WEB00252 |
+----------+
TEXT: Total number of records processed for each
LOG file.
*********************************************
SERVER ACCESS LOG = %SUB1CNT
FRCA ACCESS (CACHE) LOG = %SUB2CNT
PROXY ACCESS LOG = %SUB3CNT
PROXY ACCESS (CACHE) LOG = %SUB4CNT
AGENT LOG = %SUB5CNT
REFERER LOG = %SUB6CNT
ERROR LOG = %SUB7CNT
CONFIGURATION = %SUB9CNT
*********************************************
TYPE: Informational
REASON: To provide detail information about the input
log record count processed in DAY052.
ACTION: None
REFERENCES: Chapter 9 in this guide.
+----------+
| WEB00253 |
+----------+
TEXT: OBSERVATIONS skipped by USER EXITS in the
main data step.
USRSWPR = %WPREXIT
USRSSAL = %SALEXIT
USRSAGL = %AGLEXIT
USRSERL = %ERLEXIT
USRSRFL = %RFLEXIT
USRSSAF = %SAFEXIT
USRSSIF = %SIFEXIT
USRSMIJ = %MIJEXIT
USRSHTP = %HTPEXIT
USRSSRV = %SRVEXIT
USRSHPI = %HPIEXIT
-------------------------
TOTAL = %TOTEXIT
TYPE: Informational
REASON: This message is issued to present runtime
control counts of the number of observations
that were deleted by each of the indicated
file exits in the main DATA step.
ACTION: None
REFERENCES: None
+----------+
| WEB00254 |
+----------+
TEXT: Total number of SMF 120 records processed by
subtype.
************************************
SUBTYPE 1 (SERVER ACTIVITY):
SERVER ACTIVITY RECORDS = %S1SACNT
COMMUNICATION RECORDS = %S1CMCNT
SUBTYPE 3 (SERVER INTERVAL):
SERVER RECORDS = %S3SICNT
JVM HEAP RECORD = %S3HPCNT
SUBTYPE 5 (J2EE CONTAINER ACTIVITY):
J2EE CONTAINER RECORDS = %S5JACNT
SUBTYPE 6 (J2EE CONTAINER INTERVAL):
J2EE CONTAINER RECORDS = %S6JICNT
SUBTYPE 8 (Web Container Interval):
WebContainer Records = %S8WICNT
HttpSession Records = %S8WICNT
WebApplication Records = %S8WACNT
Servlet Records = %S8WSCNT
************************************
TYPE: Informational
REASON: This message is issued to present runtime
control counts. The numbers represent the
number of SMF type 120 records by subtypes
read from the INPUTSMF file.
ACTION: None
REFERENCES: None
+----------+
| WEB02001 |
+----------+
TEXT: No data has passed through initial selection.
Check file status and selection criteria.
Run terminating with USER ABEND 998.
TYPE: Error
REASON: The selection criteria used to subset the
data may have caused no observations to pass
through, resulting in zero observations in
the step.
ACTION: Change the selection criteria and rerun the
inquiry.
REFERENCES: None
+----------+
| WEB02002 |
+----------+
TEXT: This report is only supported through
versions V5R2 and higher.
The highest version detected in the data =
%WEBSRVVR.
TYPE: Error
REASON: Elements used in this report are only
supported at Version 5 Release 2 or higher.
If you are running a report that has two
different versions of data within it, the
highest data detected is used for the element
WEBSRVVR.
ACTION: Run this report with only data that is V5R2
or higher. If you attempt to use data
that is less than V5R2, the job will not fail
as long as there is additional data being
input from higher versions.
REFERENCES: None
+----------+
| WEB02010 |
+----------+
TEXT: The lines per page was set to less than 30.
This report requires a minimum PAGE SIZE of
30. PAGE SIZE set to 30.
TYPE: Informational
REASON: The PAGESIZE option specified a value for
page size that is less than 30. A minimum
value of 30 for the page size is required.
ACTION: Change the PAGESIZE= value to 30 or more to
avoid this message.
REFERENCES: You can change the page size by going into
MWF, selecting option 2;0, and choosing
either foreground or batch execution
parameters. Find the page length option and
specify the number of lines per printed page
for inquiry outputs.
