2. PERFORMANCE REPORTING ANALYSIS › 2.6 PR/SM LPAR Performance Analysis › 2.6.6 PR/SM LPAR Analysis Operation › 2.6.6.2 PR/SM LPAR Activity Report
2.6.6.2 PR/SM LPAR Activity Report
The PR/SM LPAR Activity Report displays the utilization and
configuration of a logical partition operating in a Central
Electronic Complex. It can be generated for the DETAIL,
DAYS, WEEKS, or MONTHS timespans if they are present in your
CA MICS database. Note that the PR/SM LPAR Activity Report
obtains its data from the HARLPC Files. If you are unsure of
the timespans supported at your installation, consult your
CA MICS System Administrator.
The PR/SM LPAR Activity Report is produced using a series of
five panels. Only the first panel is required. The others
are used to specify additional options.
/-------------------------- PR/SM LPAR Activity Report ------------------------ \
| Command ===> |
| |
| Composing CA MICS Inquiry: PRSM02 - Track LPAR Activity |
| |
| Time-span ===> MONTHS (DETAIL/DAYS/WEEKS/MONTHS) Cycle(s) ===> 01 - 02 |
| Data base ===> P (PRIMARY) _ _ _ _ |
| Allow Run-Time Override of Data Base ===> Y (Y/N) and/or Cycle(s) ===> Y (Y/N) |
| |
| Report by hour if timespan is DAYS or WEEKS ===> N (Y/N) |
| Generate a report for each value of Zone ===> N (Y/N) |
| |
| Data Selection: Allow run-time override |
| Date ===> _______ - _______ _______ - _______ ===> N (Y/N) |
| Hour ===> __ - __ __ - __ __ - __ ===> N (Y/N) |
| Zone ===> _ _ _ _ _ _ _ _ _ ===> N (Y/N) |
| Sysid ===> ____ ____ ____ ____ ____ ____ ===> N (Y/N) |
| LPAR Name ===> ________ ________ ________ ________ ________ |
| |
| |
| |
| |
| Specify extended options ===> N (Y/N) |
\----------------------------------------------------------------------------/
Figure 2-197. PR/SM LPAR Activity Report Inquiry Panel
Figure 2-197 shows a PR/SM CEC Summary Report inquiry panel.
The fields common to all PR/SM Analysis routines are
described in Section 2.6.6. The following are general
comments on this panel.
In addition to the timespan qualifier, you have the option
of selecting summaries by ZONE and HOUR. Summarization by
HOUR can be done if you are using the DAYS or WEEKS time
spans. Summarization can be specified with the Report by
hour and Generate a report for each value of Zone options.
If you specify the DAYS timespan and summarization by HOUR,
and if you request multiple cycles, a separate report is
produced for each day. If you do not specify a summarization
parameter, the report is summarized to the timespan level
(i.e., MONTHS is summarized to the month, WEEKS to the week,
DAYS to the day, and DETAIL to the RMF interval).
If no LPAR name is selected, a report will be generated for
each LPAR on each selected SYSID (or all SYSIDs if none are
specified). If more than one SYSID is generating RMF data
for the same CEC, duplicate information is retained for each
SYSID/LPAR combination. Consequently, to prevent having
duplicate reports created, you should determine one
SYSID/LPAR combination for the logical partition you wish to
have reported.
If multiple SYSIDs have created RMF data for the same complex
(for example, two different MVS systems are running in
separate logical partitions on the same CEC), then the most
comprehensive reporting will be achieved by selecting the
SYSID that was most active during the time period to be
reported.
There are four other panels in this series that you can use
to specify additional options. They are:
o Extended Options Menu
o Global Data Selection
o Alternate Input File
o Save Selected Input Observations
For a description of the Extended Options Menus refer to
Section 1.4.3.6, Specifying Common Extended Options.
