|
|
|
------------------------- Hardcopy Reports and Logs -------------------------
Command ===>
Reporting Job Stream: IMSDAILY - Daily IMS Reports
-------------------------- Hardcopy Printed Reports ------------------------- Print Reports ===> YES (YES/NO) SYSOUT Class ===> R SYSOUT Form ===> ____ Destination ===> N14R45 SYSOUT Writer ===> ________ SYSOUT Parms. ===> COPIES=3 -------------------------Hardcopy MICSLOGs and SAS Logs------------------------ Print Logs ===> ERROR (MICS/SAS/BOTH/ERROR/NO) SYSOUT Class ===> A SYSOUT Form ===> ____ Destination ===> _________________ SYSOUT Writer ===> ________ SYSOUT Parms. ===> ___________________________________________________________ Enter the RESTORE command to erase parameter overrides and use the defaults.
. . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-12. Hardcopy Reports and Logs The Hardcopy Reports and Logs panel lets you generate hardcopy reports and MICSLOG and SAS log in addition to saving inquiry outputs for later online review. You can write printed reports to a user-defined SYSOUT data set. You can also write MICSLOG and SAS log to a separate SYSOUT data set. You can use the Hardcopy Reports and Logs options to route MICF reports and logs to your data center's report management facility (for example, CA Bundl). The Hardcopy Reports and Logs panel is in two sections. The upper section applies to printed reports while the lower section applies to the MICSLOG and SAS log. The panel options are described in the paragraphs that follow. You can instruct MICF to copy ALL printed reports to the JES SYSOUT data set you define in the Hardcopy Printed Reports section of the panel. o Enter YES (or Y) following the Print Reports prompt to generate hardcopy printed reports. o You can specify SYSOUT class, destination, form number, and other SYSOUT allocation parameters to direct printed reports to the desired location. ALL printed reports from ALL inquiries in the production reporting job stream will be written to this SYSOUT file. ALL printed reports are still available for online review through the MICF Reports and Graphics option. o Enter NO (or N) following the Print Reports prompt to just save printed reports for later online review. You can change your hardcopy specification from YES to NO without deleting the SYSOUT allocation parameters. Just enter NO and END from the panel. MICF will turn off hardcopy reports, but still save your SYSOUT allocation parameters for use if you later reactivate hardcopy printed reports. You can instruct MICF to copy just the MICSLOG output, just the SAS log output, or both MICSLOG and SAS log to the JES SYSOUT data set you define in the Hardcopy MICSLOG and SAS Log section of the panel. o Enter CA MICS (or M) following the Print Logs prompt to generate hardcopy MICSLOG output. ALL MICSLOG text from ALL inquiries in the production reporting job stream will be written to the SYSOUT data set you define for hardcopy logs. SAS logs will only be retained online. o Enter SAS (or S) following the Print Logs prompt to generate hardcopy SAS log output. ALL SAS log text from ALL inquiries in the production reporting job stream will be written to the SYSOUT data set you define for hardcopy logs. MICSLOG will only be retained online. o Enter BOTH (or B) following the Print Logs prompt to write both the MICSLOG and the SAS log for each inquiry to the hardcopy (SYSOUT) file. For each inquiry, the MICSLOG will be written first, followed by the SAS log. o You also have the option to generate a hardcopy error log. Enter ERROR (or E) following the Print Logs prompt to activate the hardcopy error log. When an inquiry execution error occurs, MICF will copy the failing inquiry's MICSLOG and SAS log to the JES SYSOUT data set you define. The hardcopy error log will be empty when all inquiries execute successfully. o You can specify SYSOUT class, destination, form number, and other SYSOUT allocation parameters to direct logs to the desired location. MICSLOG and SAS log will be written to SYSOUT. ALL MICSLOG and SAS log listings are still available for online review through the MICF Reports and Graphics option. o Enter NO (or N) following the Print Logs prompt to only save MICSLOG and SAS log for later online review. You can change your hardcopy specification to NO without deleting the SYSOUT allocation parameters. Just enter NO and END from the panel. MICF will turn off hardcopy logs but still save your SYSOUT allocation parameters for use if you later reactivate hardcopy MICSLOG and SAS log. The SYSOUT data set allocation parameters on this panel default to values from the Production Reporting Hardcopy options in MICF Options, User Profile Parameters. You can tailor the defaults in MICF Options to match the SYSOUT parameters you use most often for production reporting hardcopy outputs. You can reset and erase previously specified hardcopy printed report and log options by entering the RESTORE command on the Hardcopy Reports and Logs panel. MICF will clear your hardcopy report and log specifications and redisplay the Execution and Hardcopy Output Options menu.
| Copyright © 2012 CA. All rights reserved. | Tell Technical Publications how we can improve this information |